# Air assist relay switching

**URL:** <https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301>\
**Category:** Ruida controllers\
**Created:** [June 30, 2020, 8:42pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301 "2020-06-30T20:42:11Z")\
**Posts on this page:** 15\
**Page:** 1

<div class="post-metadata">

**Author:** ![alanmccabe](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/alanmccabe/32/12844_2.png) [@alanmccabe](https://forum.lightburnsoftware.com/u/alanmccabe)\
**Post date:** [June 30, 2020, 8:42pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/1 "2020-06-30T20:42:11Z")

</div>

Apparently the new firmware .18 has an additional state for the air assist where by it switches on and off when the laser fires, this would be great and save my compressor from running but can be very annoying working on small items or engraving with the relay chatter, I wonder is it possible to add a small timer to in effect smooth out the on and offs so they happen less frequently, I was thinking of a capacitor across the relay so if the laser stops for a 1/2 second the relay still stays on and reduce the chatter. If the laser is off for more than 5 seconds the relay would stop. Just a though has anyone tried it. Can it be done in lightburn even ?

---

<div class="post-metadata">

**Author:** ![Mike\_UK](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/mike_uk/32/3342_2.png) [@Mike\_UK](https://forum.lightburnsoftware.com/u/Mike_UK)\
**Post date:** [July 1, 2020, 10:51am UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/2 "2020-07-01T10:51:16Z")

</div>

If you are using a RUIDA controller then there is a contact on the Conroller that says Wind, this is activated when the controller/Laser starts a job and will de activate when it finished the job. This is used to operate through a relay a pnematice 24V valve which you use to switch the air assist on an off. There is also a circuit design available where you can have a 3 state air circuit, air off, air low and air full power. Check [www.CloudRayLaser.com](http://www.CloudRayLaser.com) and they have the circuit diagram and a kit to assist in making the AirAssit modification.

---

<div class="post-metadata">

**Author:** ![jpjacobs](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/e47774/32.png) [@jpjacobs](https://forum.lightburnsoftware.com/u/jpjacobs)\
**Post date:** [July 1, 2020, 1:32pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/3 "2020-07-01T13:32:54Z")

</div>

Maybe a timer OFF module would suit your needs?

---

<div class="post-metadata">

**Author:** ![alanmccabe](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/alanmccabe/32/12844_2.png) [@alanmccabe](https://forum.lightburnsoftware.com/u/alanmccabe)\
**Post date:** [July 1, 2020, 1:33pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/4 "2020-07-01T13:33:22Z")

</div>

Thanks Mike, I have the air assist working ok with the firmware .15 that grounds the pin to energise to the 24 volt relay, as soon as the job starts, laser in any state on or off.

In the new firmware .18 there is an option to have the relay energise when the laser is energised tis would be great but in reality the laser is on and off so much and hence the relay is switching on and off making a terrible racket probably not good for the relay either.

---

<div class="post-metadata">

**Author:** ![alanmccabe](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/alanmccabe/32/12844_2.png) [@alanmccabe](https://forum.lightburnsoftware.com/u/alanmccabe)\
**Post date:** [July 1, 2020, 1:34pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/5 "2020-07-01T13:34:14Z")

</div>

Yep I am thinking along the lines of a relay timer JP Jacobs. going to play around a bit.

Thanks Alan

---

<div class="post-metadata">

**Author:** ![Stroonzo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/stroonzo/32/8293_2.png) [@Stroonzo](https://forum.lightburnsoftware.com/u/Stroonzo)\
**Post date:** [July 1, 2020, 2:13pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/6 "2020-07-01T14:13:30Z")

</div>

Before proceeding:

[Air assist solenoid fires rapidly on RDC6445G](https://forum.lightburnsoftware.com/t/air-assist-solenoid-fires-rapidly-on-rdc6445g/15935)

> [@Air assist solenoid fires rapidly on RDC6445G](https://forum.lightburnsoftware.com/t/air-assist-solenoid-fires-rapidly-on-rdc6445g/15935/54):
>
> G’day guys,  
> The issue of the Air Solenoid clicking on and off while the laser is firing can be resolved by adjusting the setting BLOW TYPE setting using RD Works.
> 
> There are 2 modes for Auto Air Assist Solenoid Valve:  
> 1 Blowing while LASER ON - this solenoid will click on and off each time the laser fires.  
> 2 Blowing while PROCESSING - this will click solenoid on and off for each mode set in the layers if Blowing Yes or No etc but now each time the laser fires. This is the preferred mode.
> 
> I have not been able to find the option to change the Blow Mode in Lightburn.
> 
> I have a new video on my channel showing how to change this setting.
> 
> ![](https://i.ytimg.com/vi/ZbCbLGymNhg/maxresdefault.jpg "RuiDa Setting the Air Assist Blowing Modes RDC644X RDWorks")
> 
> [RuiDa Setting the Air Assist Blowing Modes RDC644X RDWorks](https://www.youtube.com/watch?v=ZbCbLGymNhg)
> 
> Cheers Matt  
> MW Laser

---

<div class="post-metadata">

**Author:** ![alanmccabe](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/alanmccabe/32/12844_2.png) [@alanmccabe](https://forum.lightburnsoftware.com/u/alanmccabe)\
**Post date:** [July 1, 2020, 4:04pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/7 "2020-07-01T16:04:36Z")

</div>

Hi Jeff, yea I seen that I want Blowing while laser on with the tweak that I can dampen the number of times it switches maybe with a timer set to 3 seconds to hold the relay on it makes a terrible noise with that option selected at the minute

---

<div class="post-metadata">

**Author:** ![Stroonzo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/stroonzo/32/8293_2.png) [@Stroonzo](https://forum.lightburnsoftware.com/u/Stroonzo)\
**Post date:** [July 1, 2020, 4:09pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/8 "2020-07-01T16:09:59Z")

</div>

Why not use the setting for blowing while _Processing_?

---

<div class="post-metadata">

**Author:** ![alanmccabe](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/alanmccabe/32/12844_2.png) [@alanmccabe](https://forum.lightburnsoftware.com/u/alanmccabe)\
**Post date:** [July 1, 2020, 4:13pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/9 "2020-07-01T16:13:17Z")

</div>

Currently thats what I do at the minute, but as soon as the job starts the air starts and if I can save air the compressor runs less and its easier on my ears.

---

<div class="post-metadata">

**Author:** ![Stroonzo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/stroonzo/32/8293_2.png) [@Stroonzo](https://forum.lightburnsoftware.com/u/Stroonzo)\
**Post date:** [July 1, 2020, 4:26pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/10 "2020-07-01T16:26:14Z")

</div>

I read where you wired your solenoid as such:

> [@alanmccabe](#):
>
> grounds the pin to energise to the 24 volt relay, as soon as the job starts, laser in any state on or off

I read this as, you have wired your solenoid alternatively (such as on CN1 Pin 4 _Status_), opening the solenoid when the job starts, closing when the job ends (and not having layer control).

If you are wiring your solenoid on CN1 Pin 5 _Wind_, you will have discrete layer control of the solenoid. Ruida’s newest firmware also added to the discrete layer control with three states:

- pulsing wind with laser
- constant on
- constant off

Again, this is at each individual layer level.

---

<div class="post-metadata">

**Author:** ![alanmccabe](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/alanmccabe/32/12844_2.png) [@alanmccabe](https://forum.lightburnsoftware.com/u/alanmccabe)\
**Post date:** [July 1, 2020, 4:35pm UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/11 "2020-07-01T16:35:10Z")

</div>

I have it on CN1 Pin 5 Wind ok but, and pulsing wind with laser is working fine.

I just want to reduce the number of pulses for example when I wm cutting small items the laser is on and off so many times the relay is nearly thrashing as the laser switches. Sorry if I am not explaining very well.

So if I can add a small delay holding the relay on it would work. I have ordered some capacitors to try and will let you know

---

<div class="post-metadata">

**Author:** ![jpjacobs](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/e47774/32.png) [@jpjacobs](https://forum.lightburnsoftware.com/u/jpjacobs)\
**Post date:** [July 6, 2020, 9:16am UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/12 "2020-07-06T09:16:05Z")

</div>

Maybe a timer off would be an idea to achieve your goal of the relay not firing so much?  
I would prefer that over the capacitors.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [July 7, 2020, 5:19am UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/13 "2020-07-07T05:19:03Z")

</div>

Beware, some of the new firmware has a problem with controlling the Air assist ( WIND ). I had to downgrade to .15 to get some semblance of order with my almost new 6445G.

One work around, use the STATUS terminal instead of the WIND. It comes on as soon as the laser goes into action and shuts off when it goes back to the home position. I did that for quite a while until I downgraded to the .15.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [July 15, 2020, 12:47am UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/14 "2020-07-15T00:47:08Z")

</div>

Update - I wasn’t using the read / write correctly. it was strictly an operator head space error.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [August 14, 2020, 12:53am UTC](https://forum.lightburnsoftware.com/t/air-assist-relay-switching/18301/15 "2020-08-14T00:53:50Z")

</div>

Closed on August 14, 2020, 12:53am UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
