# Auto home always goes to left rear corner of my xtool, not the left front

**URL:** <https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939>\
**Category:** LightBurn Software Questions\
**Created:** [July 1, 2023, 3:24pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939 "2023-07-01T15:24:19Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![sheldonmartin](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/s/e495f1/32.png) [@sheldonmartin](https://forum.lightburnsoftware.com/u/sheldonmartin)\
**Post date:** [July 1, 2023, 3:24pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939/1 "2023-07-01T15:24:19Z")

</div>

I’m brand new here. No matter where I set my origin under settings, the laser goes to left rear corner of my machine. When I press the Y axis move button, the laser goes opposite of what I’m telling it. X axis is fine.Y axis is backwards and engraves upside down. xTool D1 Pro

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [July 1, 2023, 10:44pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939/2 "2023-07-01T22:44:25Z")

</div>

The origin that machine moves to is not dictated by Lightburn… The setting in Lightburn is to let the software know where the machines origin is located.

* * *

In a normal boot on a machine that homes, it’s determined by the controller itself.

I’m not up on these machines, but maybe @berainlb can assist… he’s got a good handle on these… if I remember correctly…

Hang in there…

😸

---

<div class="post-metadata">

**Author:** ![berainlb](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/b/85f322/32.png) [@berainlb](https://forum.lightburnsoftware.com/u/berainlb)\
**Post date:** [July 1, 2023, 11:05pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939/3 "2023-07-01T23:05:27Z")

</div>

> [@sheldonmartin](#):
>
> the laser goes to left rear corner of my machine

In general terms this is not something that you can choose. Your machine is configured to home to top-left. Your machine also happens to expect to have origin at top-left. So make sure that origin is set to top-left in Edit-\>Device Settings.

However, this implies that you didn’t use the xTool supplied .lbdev file to configure your laser.

If that’s the case then I’d suggest you create a new device using that file.

[Use LightBurn to Operate xTool D1 Pro – xTool](https://support.xtool.com/hc/en-us/articles/7317000221591-Use-LightBurn-to-Operate-xTool-D1-Pro)

---

<div class="post-metadata">

**Author:** ![sheldonmartin](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/s/e495f1/32.png) [@sheldonmartin](https://forum.lightburnsoftware.com/u/sheldonmartin)\
**Post date:** [July 1, 2023, 11:24pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939/4 "2023-07-01T23:24:05Z")

</div>

Ok. Thank you so much

---

<div class="post-metadata">

**Author:** ![sheldonmartin](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/s/e495f1/32.png) [@sheldonmartin](https://forum.lightburnsoftware.com/u/sheldonmartin)\
**Post date:** [July 1, 2023, 11:24pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939/5 "2023-07-01T23:24:48Z")

</div>

Thank you so much.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [July 31, 2023, 11:24pm UTC](https://forum.lightburnsoftware.com/t/auto-home-always-goes-to-left-rear-corner-of-my-xtool-not-the-left-front/103939/6 "2023-07-31T23:24:55Z")

</div>

Closed on July 31, 2023, 11:24pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
