# Camera Overlay Does Not Match Actual Engraving (OMTech 80W + Ruida + LightBurn 2.1.03

**URL:** <https://forum.lightburnsoftware.com/t/camera-overlay-does-not-match-actual-engraving-omtech-80w-ruida-lightburn-2-1-03/191507>\
**Category:** LightBurn Software Questions\
**Tags:** camera, ruida, omtech\
**Created:** [July 28, 2026, 9:55pm UTC](https://forum.lightburnsoftware.com/t/camera-overlay-does-not-match-actual-engraving-omtech-80w-ruida-lightburn-2-1-03/191507 "2026-07-28T21:55:18Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![luserv](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/e19b73/32.png) [@luserv](https://forum.lightburnsoftware.com/u/luserv)\
**Post date:** [July 28, 2026, 9:55pm UTC](https://forum.lightburnsoftware.com/t/camera-overlay-does-not-match-actual-engraving-omtech-80w-ruida-lightburn-2-1-03/191507/1 "2026-07-28T21:55:18Z")

</div>

Camera Overlay Does Not Match Actual Engraving (OMTech 80W + Ruida + LightBurn 2.1.03\*\*

**Machine:** OMTech 80W CO₂ laser with Ruida controller  
**Software:** LightBurn Pro 2.1.03  
**Issue:** My overhead camera overlay does not match where the laser actually engraves. I completed lens calibration and workspace alignment multiple times. I corrected the camera orientation (it was initially upside down), and the overlay is much closer now, but it is still offset. For example, if I place a rectangle in the center of a larger engraved square on the camera overlay, the laser engraves the rectangle several millimeters below where it appears on the screen. Adjusting X Shift and Y Shift improves it but does not make it accurate across the workspace.

In addition, after making adjustments, the **Frame** function sometimes stops responding, and at times **Home** and **Start** also stop responding until I restart LightBurn and/or the machine.

I need the camera overlay to be accurate because I engrave custom plaques and need precise placement. I’m trying to determine whether this is a camera calibration issue, a LightBurn 2.1.03 issue, a Ruida communication issue, or a machine profile If it **worked correctly on the previous version of LightBurn** and the problem only started after updating to **2.1.03**

---

<div class="post-metadata">

**Author:** ![MikeyH](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/m/43a26b/32.png) [@MikeyH](https://forum.lightburnsoftware.com/u/MikeyH)\
**Post date:** [July 29, 2026, 2:48am UTC](https://forum.lightburnsoftware.com/t/camera-overlay-does-not-match-actual-engraving-omtech-80w-ruida-lightburn-2-1-03/191507/2 "2026-07-29T02:48:36Z")

</div>

> [@luserv](#):
>
> I need the camera overlay to be accurate because I engrave custom plaques and need precise placement.

I just went through setting up a new camera. From what I have read, it is now a new improved process. I found it quite easy, except as noted in my Thread. Two things are extremely important: [1] **Lens Calibration** , and [2] **Material height**.

If you calibrated with 3mm plywood, then slip in a 10mm thick board, you will have issues. You must run a new camera setup process for the thicker material. You can save each calibration for each material height you will be using.

I too do cutting board engravings for a local resin artist. Meaning I ab gouing to encounter the same issues as you.

> [@Camera Install Worked, First Try](https://forum.lightburnsoftware.com/t/camera-install-worked-first-try/191418):
>
> I had avoided the camera for a long time due to all the complaints I read. I figured what I got out of it (usefulness) was not worth the hassle. Then Oz (Jason) posted some info about the new install process and I got curious. I only planned to use the camera for matching up designs with assorted pieces of scrap material. Not expecting to use it a lot, I selected about the cheapest USB camera I could find that might work. Then I added a mount adapted to my setup where I could drop the camera d…

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [August 28, 2026, 2:48am UTC](https://forum.lightburnsoftware.com/t/camera-overlay-does-not-match-actual-engraving-omtech-80w-ruida-lightburn-2-1-03/191507/3 "2026-08-28T02:48:38Z")

</div>

Closed on August 28, 2026, 2:48am UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
