# Diode vs CO2 for engraving

**URL:** <https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308>\
**Category:** Community Laser Talk\
**Created:** [September 18, 2020, 4:30am UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308 "2020-09-18T04:30:13Z")\
**Posts on this page:** 9\
**Page:** 1

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [September 18, 2020, 4:30am UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/1 "2020-09-18T04:30:14Z")

</div>

Hey all,

Have a CO2 and love it, but I’ve heard that the diode lasers being a different frequency have some better engraving on some materials. Anybody want to give me an idea, true or false?

---

<div class="post-metadata">

**Author:** ![joel1](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/c2a13f/32.png) [@joel1](https://forum.lightburnsoftware.com/u/joel1)\
**Post date:** [September 19, 2020, 6:08pm UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/2 "2020-09-19T18:08:57Z")

</div>

I have been play a lot with engraving with my CO2 laser. I can get pretty good results but the diode lasers always seem to look better. A lot of the diode engravings I see that look phenomenal took many many hours to do. To do a similar size with mine at the lowest power I can run is less than 30 minutes. So perhaps a lower power CO2 would do better ( mine is 80W ).

I have thought about making a smaller diode laser just for engraving. Either stand alone, mount to my big laser, or mount to my 3D printer.

I think the diodes can switch power levels faster, whether for grey scale or on/off than a CO2 laser, that might help too.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [September 19, 2020, 7:04pm UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/3 "2020-09-19T19:04:34Z")

</div>

Never thought about doing a CO2 / Diode combo. My big issue would be distance from the gantry to the work. With my current 80W I have around 100mm from gantry to work, and I would abhor loosing work space to mount a Diode laser beside my CO2 head. I do have around 2"+ space on the back of the gantry do to mechanical restrictions, so a back side mount might be doable. Going to have to ask if it’s possible to use my 6445G to control a diode laser.

Maybe Oz or one of the guys could chime in here if they happen to know the feasibility of it.

---

<div class="post-metadata">

**Author:** ![HalfNormal](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/halfnormal/32/554_2.png) [@HalfNormal](https://forum.lightburnsoftware.com/u/HalfNormal)\
**Post date:** [September 19, 2020, 7:52pm UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/4 "2020-09-19T19:52:52Z")

</div>

Search is your friend! 😉

> [@Combination CO2 and Diode laser in same machine](https://forum.lightburnsoftware.com/t/combination-co2-and-diode-laser-in-same-machine/8877):
>
> Another question here got me to thinking about combining a CO2 laser and Diode laser in the same machine. I know some Ruida controllers have the ability to control 2 laser heads. Would controlling the Diode laser be simple? This is just a silly idea but curious if anyone has considered it or tried it.

> [@Adding a diode to Ruida machine](https://forum.lightburnsoftware.com/t/adding-a-diode-to-ruida-machine/13630):
>
> I’m trying to add a diode laser to my Ruida CO2 machine for lower-power engraving. Specs: Ruida 6445G(EC) controller 100-watt Reci tube NUBM44 diode laser J-Tech Photonics [high-current laser driver](https://jtechphotonics.com/?page_id=126) The driver has very simple connections: power in (from its own power supply), PWM in and power out to the laser. I know these are connected properly as they’re clearly labeled on the PCB itself: I have the PWM in connected to pins 1 and 3 (LPWM2 and GND…

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [September 19, 2020, 8:21pm UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/5 "2020-09-19T20:21:27Z")

</div>

Thank you for the link. I did a search, but me and searches just but heads. Don’t know what it is, but have about a 2 in 100 luck in getting reliant search results.

Is it possible to externally save that thread? I tried various click combinations and no luck.

---

<div class="post-metadata">

**Author:** ![joel1](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/c2a13f/32.png) [@joel1](https://forum.lightburnsoftware.com/u/joel1)\
**Post date:** [September 19, 2020, 8:58pm UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/6 "2020-09-19T20:58:08Z")

</div>

On my CO2 laser, I was thinking about making a diode mount that would just replace the lens tube on my laser. Looks like I could let it sit on either side of the mirror assembly and still not have an issue at min X or max X positions.

I was thinking about using the second output of the Ruida, but I think what I would likely do it put in a switch that selects CO2 or diode. In the diode position, the CO2 LPSU would not be powered up. Because the the way I wired up my laser with it’s safety features, this would not be hard to do. This way the CO2 laser can never accidentally fire when the diode is in use.

I just need to investigate what the diodes need for an input to control power.

The other thing to keep in mind that I’m not sure how I want to handle is the windows used for CO2 lasers are not effective protection for diode. So can’t count on those at all, I’m thinking goggles when using the diode. I think most diode machines are exposed and you would need goggles anyway.

---

<div class="post-metadata">

**Author:** ![HalfNormal](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/halfnormal/32/554_2.png) [@HalfNormal](https://forum.lightburnsoftware.com/u/HalfNormal)\
**Post date:** [September 20, 2020, 1:57am UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/7 "2020-09-20T01:57:20Z")

</div>

> [@Dave01](#):
>
> Is it possible to externally save that thread? I tried various click combinations and no luck.

Click on the link then save as a bookmark.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [September 20, 2020, 2:29am UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/8 "2020-09-20T02:29:27Z")

</div>

Did that, was looking to save it externally, as in a text or pdf or even a jpg on my hard drive. Tried to print it, but only the first few pages showed up in my print preview.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [September 20, 2020, 4:00am UTC](https://forum.lightburnsoftware.com/t/diode-vs-co2-for-engraving/22308/9 "2020-09-20T04:00:41Z")

</div>

UPDATE: Evidentially The forum and Firefox don’t get along. Pulled the forum up on Internet Exploder and was able to print to pdf.
