# Does LightBurn Bridge work with the new Monport Onyx 55W laser?

**URL:** <https://forum.lightburnsoftware.com/t/does-lightburn-bridge-work-with-the-new-monport-onyx-55w-laser/120207>\
**Category:** Ruida controllers\
**Tags:** omtech-polar, monport-onyx, gweike-cloud\
**Created:** [December 4, 2023, 2:32am UTC](https://forum.lightburnsoftware.com/t/does-lightburn-bridge-work-with-the-new-monport-onyx-55w-laser/120207 "2023-12-04T02:32:55Z")\
**Posts on this page:** 1\
**Showing post:** 10

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [December 11, 2023, 8:45pm UTC](https://forum.lightburnsoftware.com/t/does-lightburn-bridge-work-with-the-new-monport-onyx-55w-laser/120207/10 "2023-12-11T20:45:33Z")

</div>

> [@berainlb](#):
>
> actually be more work

If it doesn’t work like the current models … someone had to write some code to handle the difference. That may be why it’s limited… not enough memory for it and the other default operations it does won’t fit in the machine firmware size limit?

We can only speculate… I’m usually surprised, many things Ruida does, don’t seem to make logical sense to me.

Not sure I follow about multiple IP… it only knows what you set it for…

Communications, USB/Ethernet, doesn’t seem to be it’s strong point. Case in point, using UDP… Of course that takes more code…

@NicholasL machine seems to work differently than mine. His firmware is newer, I think, but it seems to operate differently. You can read them from the two links here. They should be in one place…

> [@Relation pwm generated with different min/max controller setting](https://forum.lightburnsoftware.com/t/relation-pwm-generated-with-different-min-max-controller-setting/111441):
>
> This is a continuation of the discussion, mostly with @NicholasL Ended up trying to clarify the different results we seem to get and expect… I made two runs with three rectangular boxes, power levels at 25%, 50%, 100%. The second with 50%, 60% and 70% power levels. For these, within the laser controller, Max is 80 and Min is 40. Layer % Power Measured PWM Duty Cycle 25 40 75 76 100 80 – – 50 52 60 60 70 72 Mine seems to indicate that it is not percentage between the…

I don’t think there should be an operational difference like that… you’d have to change everything 🤷‍♂️  
If it doesn’t produce a 50% pwm with a 50% power setting, how could you check the hardware?

> [@Ruida Min and Max Power% rescales actual power output?](https://forum.lightburnsoftware.com/t/ruida-min-and-max-power-rescales-actual-power-output/107903/5):
>
> Hi Jack, That’s interesting, well, based on Ruida settings at min power 20% and max power 80% I have listed below the test values sent from LightBurn (in ‘Line’ mode with min and max power the same) along with the corresponding power values I would expect the PWM signal to be delivering to the power supply - which I have confirmed to be correct on a scope. If you get the chance to check some of these other values from your system just to confirm what is happening for you I would appreciate it.…

Someone needs to get there hands on with one of these and add on a console so we can tell what it’s doing.

😸

---

_[View the full topic](https://forum.lightburnsoftware.com/t/does-lightburn-bridge-work-with-the-new-monport-onyx-55w-laser/120207)._
