# 🍆 Don’t talk bad about a GlowForge or they will sue you…(see article) when your overpriced laser sucks and people know it you have to resort to lawsuits to make money

**URL:** <https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486>\
**Category:** Community Laser Talk\
**Created:** [February 29, 2024, 4:35am UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486 "2024-02-29T04:35:30Z")\
**Posts on this page:** 9\
**Page:** 2

<div class="post-metadata">

**Author:** ![Sasquatch](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/sasquatch/32/126858_2.png) [@Sasquatch](https://forum.lightburnsoftware.com/u/Sasquatch)\
**Post date:** [August 7, 2025, 12:53pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/21 "2025-08-07T12:53:46Z")

</div>

I did not get a chance to dig into their information too deep. What are the costs associated with the Titan Series?

Thanks

Sas

---

<div class="post-metadata">

**Author:** ![HalfNormal](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/halfnormal/32/554_2.png) [@HalfNormal](https://forum.lightburnsoftware.com/u/HalfNormal)\
**Post date:** [August 7, 2025, 1:12pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/22 "2025-08-07T13:12:45Z")

</div>

Jonathan, welcome to the Lightburn forum! I have followed your journey from trying to help the users of Glowforges to being banned from their forum. It was just a matter of time before they imploded.

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [August 7, 2025, 1:25pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/23 "2025-08-07T13:25:44Z")

</div>

> [@Geriatric](#):
>
> MOPA capable of a 51" x 35" work area

I don’t think this is a probably size for a MOPA, unless you go with the combination of fiber on a gantry. They have labeled these flying head galvo, I think.

The largest area I can use is about 300x300mm. The only way to get that is to use a long lens. To cover 51" x 35" (1300x890mm) seems like you’d need a very long lens along with it mounted on the ceiling. The resultant spot from such a long lens would be huge.

I don’t do anything commercial, but how these work seems like you are limited in size for anything that’s really functional.

If you know otherwise, please advise.

😺

---

<div class="post-metadata">

**Author:** ![macgeek](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/macgeek/32/109629_2.png) [@macgeek](https://forum.lightburnsoftware.com/u/macgeek)\
**Post date:** [August 7, 2025, 1:28pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/24 "2025-08-07T13:28:58Z")

</div>

Oh yea, blacklisted from Community, and from Glowforge, they would not even let me buy wood! - silly wabbits!

---

<div class="post-metadata">

**Author:** ![macgeek](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/macgeek/32/109629_2.png) [@macgeek](https://forum.lightburnsoftware.com/u/macgeek)\
**Post date:** [August 7, 2025, 1:30pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/25 "2025-08-07T13:30:09Z")

</div>

a LOT of investors, Got screwed badly … BADLY

---

<div class="post-metadata">

**Author:** ![Geriatric](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/geriatric/32/68873_2.png) [@Geriatric](https://forum.lightburnsoftware.com/u/Geriatric)\
**Post date:** [August 7, 2025, 3:54pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/26 "2025-08-07T15:54:09Z")

</div>

My understanding is the gantry will move to the area to be lasered, do the marking, then move to the next area and do the same. There is already one other that works the same way but, if I remember correctly, it is a Diode and Fiber combination.  
Unfortunately, there is not much information about it yet which is why I want to see it in action before I decide. As to the pricing, I haven’t asked yet but allowing for the fact it is RF/MOPA combination, I expect it to be similar in cost to a Nova Plus 51 and Aurora combined.  
Once I find where in Canada one will be, I can go take a look. Hopefully there will be one in Calgary because it’s only a three hour drive but Westjet can take me where I need to go.  
It will still be cheaper than replacing the Epilog.

---

<div class="post-metadata">

**Author:** ![Geriatric](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/geriatric/32/68873_2.png) [@Geriatric](https://forum.lightburnsoftware.com/u/Geriatric)\
**Post date:** [August 7, 2025, 3:55pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/27 "2025-08-07T15:55:56Z")

</div>

I downloaded LaserMaker as well. The impression I get is that it may be Cloud based. If that is the case, I won’t be using it.

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [August 7, 2025, 4:13pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/28 "2025-08-07T16:13:16Z")

</div>

> [@Geriatric](#):
>
> impression I get is that it may be Cloud based

Some people are of the mind, that cloud data processing will take over, but devices like glowforge have never had a good following when you need an internet connection to just operate the machine.

I’ve been around computers and such for close to 1/2 a century, requiring someones stuff to work remotely has never been a good option.

I will never spend money on them, you always get the short end of the stick.. IMHO 🤔

> [@Geriatric](#):
>
> understanding is the gantry will move to the area to be lasered, do the marking, then move to the next area and do the same

Might want to check this thread.

> [@Does Lightburn support a flying galvo configuration?](https://forum.lightburnsoftware.com/t/does-lightburn-support-a-flying-galvo-configuration/172502):
>
> I was hoping someone with Lightburn could answer us about this product. It’s a flying galvo head or a galvo on a gantry machine. It’s supposed to [go to Kickstarter this month](https://www.kickstarter.com/projects/accelaser/accelaser-hd1-worlds-first-dual-laser-with-flying-3d-galvo?ref=8gjw7y). Is it really Lightburn compatible ?.. claiming they have been in touch with Lightburn during the development, any comments? Wonder how some of this is implemented, such as LIDAR Z control, and assume gcode? Here is a quick video on two machines.. Originally posted by @HalfNormal on the Markers forum. [[EVE…](https://www.youtube.com/watch?v=q7zNaJnNbks)

😺

---

<div class="post-metadata">

**Author:** ![RalphU](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/ralphu/32/42743_2.png) [@RalphU](https://forum.lightburnsoftware.com/u/RalphU)\
**Post date:** [August 7, 2025, 5:09pm UTC](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486/29 "2025-08-07T17:09:12Z")

</div>

> [@Geriatric](#):
>
> I downloaded LaserMaker as well. The impression I get is that it may be Cloud based. If that is the case, I won’t be using it.

Not cloud based. Works on Windows and also a Mac version.

 ![image](https://forum.lightburnsoftware.com/uploads/default/original/3X/4/d/4d1d2dc8a9a6914de3061cda10561fed7c377127.png)

[Previous page](https://forum.lightburnsoftware.com/t/don-t-talk-bad-about-a-glowforge-or-they-will-sue-you-see-article-when-your-overpriced-laser-sucks-and-people-know-it-you-have-to-resort-to-lawsuits-to-make-money/131486.md?page=1)
