# ERROR MESSAGE between LightBurn and Ortur LM3

**URL:** <https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085>\
**Category:** LightBurn Software Questions\
**Tags:** ortur\
**Created:** [August 25, 2026, 6:17pm UTC](https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085 "2026-08-25T18:17:28Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![PauloCNC](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/p/d07c76/32.png) [@PauloCNC](https://forum.lightburnsoftware.com/u/PauloCNC)\
**Post date:** [August 25, 2026, 6:17pm UTC](https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085/1 "2026-08-25T18:17:28Z")

</div>

Hi Guys,

I am using the latest version of LightBurn and an Ortur LM3 without any problems till today.

I get an error message

ALARM:2  
G-code motion target exceeds machine travel. Machine position safely retained. Alarm may be unlocked. (Right-click the ‘Devices’ button to reset the connection) On or near line 3:

The job is 220mm x 240mm so its smaller than the bed size.

I would appreciate any assistance

Paul

---

<div class="post-metadata">

**Author:** ![brewster](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/b/ac8455/32.png) [@brewster](https://forum.lightburnsoftware.com/u/brewster)\
**Post date:** [August 26, 2026, 12:01am UTC](https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085/2 "2026-08-26T00:01:26Z")

</div>

Try a “select all” and look for any tiny hairs outside the workspace grid.

---

<div class="post-metadata">

**Author:** ![parsec](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/parsec/32/118933_2.png) [@parsec](https://forum.lightburnsoftware.com/u/parsec)\
**Post date:** [August 26, 2026, 12:35am UTC](https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085/3 "2026-08-26T00:35:35Z")

</div>

After the Select All, Create a Rubber Band Outline to better see the position of the trash shapes.

> **[Create Rubber-Band Outline - LightBurn User Guide](https://docs.lightburnsoftware.com/latest/Reference/CreateRubberBandOutline/)**
>
> LightBurn's Create Rubber-Band Outline tool automaticalyl makes a new shape outlining your selected graphics.

Also review the Alarm.2 doc:

> **[ALARM:2 - GRBL Errors - LightBurn User Guide](https://docs.lightburnsoftware.com/latest/Troubleshooting/GRBLErrors/#alarm2)**
>
> GRBL devices have a number of different alarms and error codes you may encounter. These will be visible in the Console Window. | Explanations of common GRBL errors.

---

<div class="post-metadata">

**Author:** ![JohnJohn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/johnjohn/32/37027_2.png) [@JohnJohn](https://forum.lightburnsoftware.com/u/JohnJohn)\
**Post date:** [August 26, 2026, 9:30pm UTC](https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085/4 "2026-08-26T21:30:05Z")

</div>

> [@PauloCNC](#):
>
> G-code motion target exceeds machine travel.

If you are engraving a Filled closed shape or an Image, overscan can be a cause for this.

In LightBurn, click the Icon that looks like a Flat Panel Monitor in the top middle of the toolbar. This launches a preview feature that simulates the machine area and the commands being sent to the engraver.

Red lines show the traversal moves where the machine moves but does not engrave (if the Show traversal moves switch is enabled).

The most often seen cause for the Alarm:2 here is the overscan going outside the work area.

The easiest way to reduce the overscan is to reduce the speed and power of your engraving. Reducing the size of the engraving is a good option if you’re in a hurry.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [September 25, 2026, 9:31pm UTC](https://forum.lightburnsoftware.com/t/error-message-between-lightburn-and-ortur-lm3/192085/6 "2026-09-25T21:31:21Z")

</div>

Closed on September 25, 2026, 9:31pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
