# Foxalien Reizer 20W laser cutting

**URL:** <https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790>\
**Category:** Community Laser Talk\
**Created:** [March 15, 2023, 8:41am UTC](https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790 "2023-03-15T08:41:50Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Rifca](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/59ef9b/32.png) [@Rifca](https://forum.lightburnsoftware.com/u/Rifca)\
**Post date:** [March 15, 2023, 8:41am UTC](https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790/1 "2023-03-15T08:41:50Z")

</div>

Good morning,  
I am new to laser cutting and tried it for the first time yesterday. I tried to cut a vector downloaded from the internet. I was cutting 3mm thick plywood and the speed was 100mm/sec and the power was 100%. I am not using air assist just yet, (got one on order) Anyway the laser did 100 passes and only managed to break through the plywood in a few areas the rest was still firmly attached. There was minimal scorching of the surface of the plywood which was good but I was disappointed that the laser took so many passes and still didn’t complete the operation. Is this what I should have expected?  
The laser is a 20W laser which I think should be powerful enough to do a better job.  
Any advice would be greatly appreciated.  
Regards Mick

---

<div class="post-metadata">

**Author:** ![Will\_vl](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/w/848f3c/32.png) [@Will\_vl](https://forum.lightburnsoftware.com/u/Will_vl)\
**Post date:** [March 15, 2023, 12:16pm UTC](https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790/2 "2023-03-15T12:16:05Z")

</div>

In Device Settings check _S-value max_. This should be at 1000. It’s sometimes found @ 255.

Change the value if needed and re-run your test.

---

<div class="post-metadata">

**Author:** ![Rifca](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/59ef9b/32.png) [@Rifca](https://forum.lightburnsoftware.com/u/Rifca)\
**Post date:** [March 15, 2023, 2:43pm UTC](https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790/3 "2023-03-15T14:43:54Z")

</div>

Thanks Will, I will have a look tonight.  
regards Mick

---

<div class="post-metadata">

**Author:** ![Rifca](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/59ef9b/32.png) [@Rifca](https://forum.lightburnsoftware.com/u/Rifca)\
**Post date:** [March 16, 2023, 12:04pm UTC](https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790/4 "2023-03-16T12:04:05Z")

</div>

I contacted Foxalien and this is their response which I will check tonight.

May I ask did you set the correct focus point?  
Please clean the laser lens to make a test.  
Please enter $$ in the console window to check default maximum S value whether $30=1000 or $30=10000.  
If $30=1000, please set maximum S value to 1000 on software.  
If $30=10000, please set maximum S value to 10000 on software. Otherwise, S1000 is just 1/10 of the laser power. It is too weak to engrave.

---

<div class="post-metadata">

**Author:** ![Rifca](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/59ef9b/32.png) [@Rifca](https://forum.lightburnsoftware.com/u/Rifca)\
**Post date:** [March 17, 2023, 8:46am UTC](https://forum.lightburnsoftware.com/t/foxalien-reizer-20w-laser-cutting/94790/5 "2023-03-17T08:46:14Z")

</div>

I checked the settings which were correct, I had another go at recutting the same shape and reduced the speed from 100mm/sec to 20mm/sec and after 5 passes the shape was cut out properly.
