# Greyscale for co2 laser 40 watt

**URL:** <https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642>\
**Category:** Tips and Tricks\
**Created:** [May 6, 2020, 4:21pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642 "2020-05-06T16:21:40Z")\
**Posts on this page:** 11\
**Page:** 1

<div class="post-metadata">

**Author:** ![Angie](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/ec9cab/32.png) [@Angie](https://forum.lightburnsoftware.com/u/Angie)\
**Post date:** [May 6, 2020, 4:21pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/1 "2020-05-06T16:21:40Z")

</div>

can greyscale be used in a co2 40watt laser? If so, can anyone give me any info on how to do a photo from a camera, not a internet download photo.

---

<div class="post-metadata">

**Author:** ![Squid](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/squid/32/18934_2.png) [@Squid](https://forum.lightburnsoftware.com/u/Squid)\
**Post date:** [May 6, 2020, 4:31pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/2 "2020-05-06T16:31:33Z")

</div>

Yes but not really recommended.  
Having said that and after long fine tuning i was able to reach this outcome on my co2 K40

> [@GrayScale Engraving](https://forum.lightburnsoftware.com/t/grayscale-engraving/8551/10):
>
> SKR 1.3 32bit 100mhz Controller. I don’t want to judge it too soon and before i will have a PC 1m away with a good USB cable. so far i am very happy. This is an image i just downloaded from the internet and without changing any settings from my grayscale calibration image, this is what I’m getting (On a gray 2mm EskaBoard): I am very pleased.

---

<div class="post-metadata">

**Author:** ![Angie](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/ec9cab/32.png) [@Angie](https://forum.lightburnsoftware.com/u/Angie)\
**Post date:** [May 6, 2020, 4:35pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/3 "2020-05-06T16:35:57Z")

</div>

Thank you for your advice. I will try a download pic to see what my results might be.

---

<div class="post-metadata">

**Author:** ![travisr100](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/t/a5b964/32.png) [@travisr100](https://forum.lightburnsoftware.com/u/travisr100)\
**Post date:** [May 6, 2020, 6:59pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/4 "2020-05-06T18:59:34Z")

</div>

Am I the only one that thinks Grayscale should be renamed to something like Depth?

---

<div class="post-metadata">

**Author:** ![Squid](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/squid/32/18934_2.png) [@Squid](https://forum.lightburnsoftware.com/u/Squid)\
**Post date:** [May 6, 2020, 7:20pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/5 "2020-05-06T19:20:55Z")

</div>

> [@travisr100](#):
>
> Am I the only one that thinks Grayscale should be renamed to something like Depth?

Are you familiar with this technique?  
Naming feature can be tricky…

> [@First attempt at 3D grayscale engraving](https://forum.lightburnsoftware.com/t/first-attempt-at-3d-grayscale-engraving/5467):
>
> This koi scene and the grayscale test square below are my first attempt at 3D laser engraving. Both are 0.5" thick pieces of walnut. This circle is 3.5" in diameter. The max depth of the burn is 0.15". I burned it with LightBurn on a 100 W CO2 laser in a single ~40 min pass. LightBurn Parameters: Mode: Image Speed: 150 mm/s Max Power: 100% Min Power: 19% Bi-directional scanning: On Line Interval: 0.03 mm (847 DPI) Image Mode: Grayscale Number of Pas…

---

<div class="post-metadata">

**Author:** ![DougL](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/b19c9b/32.png) [@DougL](https://forum.lightburnsoftware.com/u/DougL)\
**Post date:** [May 6, 2020, 7:24pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/6 "2020-05-06T19:24:08Z")

</div>

this might be helpful - [https://www.thingiverse.com/thing:2968556](https://www.thingiverse.com/thing:2968556)

---

<div class="post-metadata">

**Author:** ![travisr100](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/t/a5b964/32.png) [@travisr100](https://forum.lightburnsoftware.com/u/travisr100)\
**Post date:** [May 6, 2020, 8:05pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/7 "2020-05-06T20:05:34Z")

</div>

@Squid yes, I am. Why I think it should be renamed Depth. People see it and think it’s what they should use to engrave a grayscale photo when in reality they should be using one of the dithering strategies.

---

<div class="post-metadata">

**Author:** ![Squid](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/squid/32/18934_2.png) [@Squid](https://forum.lightburnsoftware.com/u/Squid)\
**Post date:** [May 6, 2020, 8:13pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/8 "2020-05-06T20:13:17Z")

</div>

GrayScale looks amazing with Diode Lasers.  
I am not saying no to depth, I am just saying it is tricky to name features. not an easy task.

---

<div class="post-metadata">

**Author:** ![travisr100](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/t/a5b964/32.png) [@travisr100](https://forum.lightburnsoftware.com/u/travisr100)\
**Post date:** [May 6, 2020, 8:13pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/9 "2020-05-06T20:13:40Z")

</div>

True, I hadn’t considered diodes. Perhaps Variable Power then.

---

<div class="post-metadata">

**Author:** ![Squid](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/squid/32/18934_2.png) [@Squid](https://forum.lightburnsoftware.com/u/Squid)\
**Post date:** [May 6, 2020, 8:22pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/10 "2020-05-06T20:22:04Z")

</div>

I am not using Lightburn voting system Fider. maybe you should.

> **[LightBurn](https://lightburn.fider.io/)**
>
> Have a feature you'd love to see in LightBurn? Suggest it here. We actually read these things. Please be specific, and include the type of contr

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [June 5, 2020, 8:23pm UTC](https://forum.lightburnsoftware.com/t/greyscale-for-co2-laser-40-watt/15642/11 "2020-06-05T20:23:50Z")

</div>

Closed on June 5, 2020, 8:23pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
