# Help! Shock and Movement detected! how do I make it stop doing this!

**URL:** <https://forum.lightburnsoftware.com/t/help-shock-and-movement-detected-how-do-i-make-it-stop-doing-this/78636>\
**Category:** Ortur Lasers\
**Tags:** grbl, ortur-laser-master-2\
**Created:** [October 11, 2022, 8:24am UTC](https://forum.lightburnsoftware.com/t/help-shock-and-movement-detected-how-do-i-make-it-stop-doing-this/78636 "2022-10-11T08:24:37Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Sarahjane](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/s/c0e974/32.png) [@Sarahjane](https://forum.lightburnsoftware.com/u/Sarahjane)\
**Post date:** [October 11, 2022, 8:24am UTC](https://forum.lightburnsoftware.com/t/help-shock-and-movement-detected-how-do-i-make-it-stop-doing-this/78636/1 "2022-10-11T08:24:37Z")

</div>

Homing  
ok  
Starting stream  
Layer C00  
[SC7A20:(335) Shock and Movement detected! Check TroubleShooting Section in User Manual.]  
Ortur Laser Master 2 Pro S2 Ready!  
OLF:OLF 185.  
OLH:OLM\_ESP\_PRO\_V1.2.  
OLM: GENERAL.  
[MSG: Flame detector active,Ambient infrared value:0]  
Grbl 1.1f [‘$’ for help]  
[MSG:‘$H’|‘$X’ to unlock]

---

<div class="post-metadata">

**Author:** ![Mooseuk](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/mooseuk/32/26201_2.png) [@Mooseuk](https://forum.lightburnsoftware.com/u/Mooseuk)\
**Post date:** [October 11, 2022, 10:46am UTC](https://forum.lightburnsoftware.com/t/help-shock-and-movement-detected-how-do-i-make-it-stop-doing-this/78636/2 "2022-10-11T10:46:10Z")

</div>

I found this by doing a search of this forum:

I had this problem too, just adding what worked for me, in case it helps anyone else struggling with the same.

I had to change the **$262** value to change the G-shock threshold.

I ended up **disabling mine entirely by setting $262=0**. This means I will _not_ get an alarm if the laser cutter falls, but I never leave it unattended while in use, so this is fine for me, but please take the time to consider this as you are disabling a safety feature. Please note, too, this fix [only works for firmware 1.78](https://forum.lightburnsoftware.com/t/ortur-laser-master-2-pro-s1-s2-firmware-update/54848) (or, presumably, later), so you might need to [update your firmware](https://ortur.tech/latest-firmware/) first.  
If you wish to disable your sensor entirely, go to the console window in LightBurn (while you are connected to your Ortur) and type _$262=0_ and hit enter.

If you’re having trouble with this value ‘sticking’ (for example you get this error again after re-starting/resetting your machine, or after changing firmware), you can also add this command to the start GCode for your laser (Edit\>Device Settings\>GCode\>type it into the ‘StartGCode’ box\>Hit OK). This will mean that it will turn off the sensor before every job that you run, so it’s sort of a backup. _Side note, but it’s also handy to add $H to this box too, to home your machine before each cut, in case you haven’t got it in there already._

You also **don’t have to entirely disable the shock sensor** , you _can_ just change the threshold value, if you wish _(this should work in earlier versions of the firmware, too)_. You can check the current threshold value by typing $$ into the console in LightBurn (which will give you a list of all current values for all settings for your connected machine). From there you can set it to a different value by typing _$262=[number]_ (e.g _$262=500_ to set it to 500).

Here’s a list of [all the commands for ortur](https://forum.lightburnsoftware.com/t/keep-getting-movement-error-and-alarms/46976/10) and their default values (I had a hard time finding these, so I’m posting it here in case it’s handy for others!).

Hope this helps someone else!

---

<div class="post-metadata">

**Author:** ![BillieRuben](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/billieruben/32/39566_2.png) [@BillieRuben](https://forum.lightburnsoftware.com/u/BillieRuben)\
**Post date:** [October 12, 2022, 8:53pm UTC](https://forum.lightburnsoftware.com/t/help-shock-and-movement-detected-how-do-i-make-it-stop-doing-this/78636/3 "2022-10-12T20:53:22Z")

</div>

Haha! I was just about to dig out a link to that post you copied, it was mine! Thanks for doing the legwork for me! 😃

Here’s a link anyway, just in case. And I’m happy to answer any other questions, because it caused me quite a bit of frustration when I first got mine!

> [@Cant complete a burn due to Shock and Movement detected!](https://forum.lightburnsoftware.com/t/cant-complete-a-burn-due-to-shock-and-movement-detected/35877/4):
>
> In the console window. Type: $$ and press enter, and that will emit all the current settings. The one next to $33 is the current value of it. If you typed: $33=400 (and pressed enter) That would set the value to 400.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [November 11, 2022, 8:54pm UTC](https://forum.lightburnsoftware.com/t/help-shock-and-movement-detected-how-do-i-make-it-stop-doing-this/78636/4 "2022-11-11T20:54:21Z")

</div>

Closed on November 11, 2022, 8:54pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
