Jog State occuring while framing, locked out, error 9

it keeps stopping and locking me out while im trying to frame my project and line it up. when i get the burn started it runs just fine without stopping or any issues, but im having a real Hard friggin time squaring my material up because every time i frame it stops halfway through.
ive looked on the forums and tried all the things and im worried ive gone and goofed one of the hundreds of settings up
so here is what it tells me when it fails to frame
and below that is what my settings are currently at

Starting stream

[SC7A20:(400) Shock and Movement detected! Check TroubleShooting Section in User Manual.]

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 187.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Warning: Flame Sensor Disabled by User OverRide]

[MSG: Flame detector active,Ambient infrared value:0]

Grbl 1.1f [‘$’ for help]

[MSG:‘$H’|‘$X’ to unlock]

Stream completed in 0:40

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 187.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Warning: Flame Sensor Disabled by User OverRide]

[MSG: Flame detector active,Ambient infrared value:0]

Grbl 1.1f [‘$’ for help]

[MSG:‘$H’|‘$X’ to unlock]

error:9

G-code locked out during alarm or jog state.

[MSG:Caution: Unlocked]

ok

$$

$0=5.0

$1=100

$2=0

$3=6

$4=7

$5=7

$6=1

$10=2047

$11=0.050

$12=0.002

$13=0

$14=6

$15=0

$16=1

$17=4

$18=0

$19=0

$20=1

$21=1

$22=1

$23=7

$24=600.000

$25=3000.000

$26=100

$27=3.000

$28=0.100

$29=0.0

$30=1000.

$31=0.

$32=1

$33=400.000

$34=0.000

$35=0.000

$36=100.000

$37=0

$39=1

$40=1

$41=0

$42=1

$43=1

$44=3

$45=0

$46=0

$56=1.000

$57=1800.000

$58=395.000

$59=6000.000

$60=0

$61=0

$62=0

$63=3

$64=1

$65=0

$100=80.000

$101=80.000

$102=2124.000

$110=10200.000

$111=10200.000

$112=600.000

$120=2200.000

$121=1800.000

$122=200.000

$130=400.000

$131=400.000

$132=100.000

$259=0

$260=70

$261=0

$262=400

$263=30

$264=0

$265=50

$266=100

$267=0

$268=0

$269=0

$270=5120

ok

This wouldn’t affect what you’re dealing with but is there a reason you changed the PWM frequency to 400? Normally this is 1000 for your laser.

As for the shock detection, are you getting a lot of shaking/movement in your machine? How is the machine situated and have you done a thorough mechanical review that all componetns are square, aligned, well fastened, and moving smoothly?

This is not a common failure on these machines so my first reaction is that there’s likely something actually wrong.

You can adjust the sensitivity of shock sensor by changing $262 value (default 400) but I’d suggest you identify what’s causing the issue. You could change this value to 0 to turn off the sensor while you troubleshoot or if you can’t be bothered. Mechanical issues are likely to result in other issues downstream, however.

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.