# Lightburn burns everything way too big!

**URL:** <https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773>\
**Category:** GRBL\
**Created:** [May 24, 2022, 7:03pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773 "2022-05-24T19:03:02Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![RubiconSC](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/d78d45/32.png) [@RubiconSC](https://forum.lightburnsoftware.com/u/RubiconSC)\
**Post date:** [May 24, 2022, 7:03pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/1 "2022-05-24T19:03:03Z")

</div>

I have a DIY laser diode machine frame 400mm x 400mm working area with a Eleksmaker Mana SE controller running grbl 1.1h and a Neje n40630 laser. As an example I can type " hello" and the dimensions are 53.xx by 18.xx in Lightburn…when I start the machine… what is burns is almost 3 times that size. This happens with everything I try to burn. I need some help please. I am new to Lightburn. Many thanks!

---

<div class="post-metadata">

**Author:** ![berainlb](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/b/85f322/32.png) [@berainlb](https://forum.lightburnsoftware.com/u/berainlb)\
**Post date:** [May 24, 2022, 7:09pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/2 "2022-05-24T19:09:36Z")

</div>

You’re most likely dealing with a situation where you GRBL configuration is incorrect for your laser.

Specifically, the steps/mm configuration described here:

> #### $100, $101 and $102 – [X,Y,Z] steps/mm
> 
> Grbl needs to know how far each step will take the tool in reality. To calculate steps/mm for an axis of your machine you need to know:
> 
> - The mm traveled per revolution of your stepper motor. This is dependent on your belt drive gears or lead screw pitch.
> - The full steps per revolution of your steppers (typically 200)
> - The microsteps per step of your controller (typically 1, 2, 4, 8, or 16). _Tip: Using high microstep values (e.g., 16) can reduce your stepper motor torque, so use the lowest that gives you the desired axis resolution and comfortable running properties._
> 
> The steps/mm can then be calculated like this: `steps_per_mm = (steps_per_revolution*microsteps)/mm_per_rev`
> 
> Compute this value for every axis and write these settings to Grbl.

LightBurn provides a way of calibrating these settings if you go to Edit-\>Machine Settings-\>Calibrate Axis.

Or else you can calibrate by hand and update the GRBL configuration.

---

<div class="post-metadata">

**Author:** ![pauldg123](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/pauldg123/32/773_2.png) [@pauldg123](https://forum.lightburnsoftware.com/u/pauldg123)\
**Post date:** [May 25, 2022, 4:28am UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/3 "2022-05-25T04:28:51Z")

</div>

Maybe you have set the controller to inches instead of mm? 1 inch = 2.54cm so almost 3x bigger…

---

<div class="post-metadata">

**Author:** ![RubiconSC](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/d78d45/32.png) [@RubiconSC](https://forum.lightburnsoftware.com/u/RubiconSC)\
**Post date:** [May 25, 2022, 2:47pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/4 "2022-05-25T14:47:15Z")

</div>

Thanks very much for your assistance…I will do that this afternoon.

---

<div class="post-metadata">

**Author:** ![RubiconSC](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/d78d45/32.png) [@RubiconSC](https://forum.lightburnsoftware.com/u/RubiconSC)\
**Post date:** [May 25, 2022, 2:50pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/5 "2022-05-25T14:50:45Z")

</div>

As far as I can tell both Lightburn and the controller are set to mm. in GRBL $13=0. In Lightburn Units/Grids are set to mm/min. Apparently, in an older version (?) of GRBL…$20 and $21 were the inch/mm settings. There has to be something I have missed…thanks for your help!! Your reasoning was spot on though as the burn is almost three times as large.

---

<div class="post-metadata">

**Author:** ![RubiconSC](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/r/d78d45/32.png) [@RubiconSC](https://forum.lightburnsoftware.com/u/RubiconSC)\
**Post date:** [May 25, 2022, 6:28pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/6 "2022-05-25T18:28:44Z")

</div>

Thanks very much…that fixed it! I don’t really understand why it was that far off…but it works now at any rate. Thanks! By the way…I used the calibrate axis within Lightburn.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [June 24, 2022, 6:29pm UTC](https://forum.lightburnsoftware.com/t/lightburn-burns-everything-way-too-big/67773/7 "2022-06-24T18:29:28Z")

</div>

Closed on June 24, 2022, 6:29pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
