# Monport GM 30w MOPA isn't displaying a frame

**URL:** <https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797>\
**Category:** LightBurn Hardware Compatibility\
**Tags:** mac, windows\
**Created:** [November 10, 2025, 8:31pm UTC](https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797 "2025-11-10T20:31:55Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![ErikB](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/e/e8c25b/32.png) [@ErikB](https://forum.lightburnsoftware.com/u/ErikB)\
**Post date:** [November 10, 2025, 8:31pm UTC](https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797/1 "2025-11-10T20:31:56Z")

</div>

I have tried to follow the ridiculous instructions from Monport for setting up my laser with my MacBook Pro. I’m able to get Lightburn to recognize the laser and it says connected. I drew a square in the middle of the screen and then clicked Frame, but there is nothing being projected. I’ve read a couple posts about the 60w version, and changed my settings accordingly, but still no frame. I’ve reset to what Monport’s video (which was done on Lightburn 1.7), and I’m not sure where to go from here. Their BSL software only works on Windows and they said I can only use Lightburn for a Mac.

 ![image](https://forum.lightburnsoftware.com/uploads/default/original/3X/a/4/a40c1ecf23346010750a0f43e20884ceba9e716e.png)

 ![Basic Settings](https://forum.lightburnsoftware.com/uploads/default/original/3X/0/d/0d6a4eceea9b97c96356b32b407166e2f35b9282.png)

The red dot offsets came from the plate stuck to the side of the laser, which says Parameter for Lightburn. Printing actually says: “Offset PosX: -0. 400mm Offset. PosY: -0. 400mm. Size ScaleX: 1. 010. Size ScaleY: 1. 013.

There’s no explanation as to what to do with this data, and the only place it seemed to fit was in the parameter for red dot.

Any ideas?

Thanks,

Erik

---

<div class="post-metadata">

**Author:** ![micrololin](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/micrololin/32/46353_2.png) [@micrololin](https://forum.lightburnsoftware.com/u/micrololin)\
**Post date:** [November 10, 2025, 8:41pm UTC](https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797/2 "2025-11-10T20:41:22Z")

</div>

I don’t have the Monport but the setting ”red dot always on” is checked in my setup.

---

<div class="post-metadata">

**Author:** ![ErikB](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/e/e8c25b/32.png) [@ErikB](https://forum.lightburnsoftware.com/u/ErikB)\
**Post date:** [November 10, 2025, 9:03pm UTC](https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797/3 "2025-11-10T21:03:28Z")

</div>

Thanks. I checked the box for always on, but still no frame. I’m wondering if the offset data should be ignored.

---

<div class="post-metadata">

**Author:** ![ErikB](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/e/e8c25b/32.png) [@ErikB](https://forum.lightburnsoftware.com/u/ErikB)\
**Post date:** [November 10, 2025, 9:32pm UTC](https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797/4 "2025-11-10T21:32:30Z")

</div>

Ok, I’m not sure what I did, but now the laser is drawing a frame box. Sorry. This is my first laser and the first time I’ve tried to use Lightburn.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [December 10, 2025, 9:33pm UTC](https://forum.lightburnsoftware.com/t/monport-gm-30w-mopa-isnt-displaying-a-frame/184797/5 "2025-12-10T21:33:16Z")

</div>

Closed on December 10, 2025, 9:33pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
