# Neje laser not connected in lightburn

**URL:** <https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886>\
**Category:** OS Specific\
**Tags:** grbl, linux, neje\
**Created:** [March 12, 2024, 2:02pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886 "2024-03-12T14:02:39Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 12, 2024, 2:02pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/1 "2024-03-12T14:02:39Z")

</div>

Neje laser cutter not recognized in lightburn  
I have just acquired Lightburn (license key) 1.5.02. On the trial version I had no problems of recognise. However, it is impossible to connect my laser cutter to the licensed version. I get the following message: “Failed to open port - already in use?”  
I read what I found on the forum and applied:

- test my USB port: it is recognized with a USB key but does not recognize the machine.
- test my USB cable: it does not present a problem in another configuration.
- uninstall lightburn 1.5.02 and reinstall it: still does not recognize the machine.
- delete the config, turn off the machine, close lightburn, turn off the PC, restart everything: still no recognition.
- delete lightburn and reinstall lightburn with appimage but same problem
- the ch340 driver is ok
- the material is ok and work in neje application.  
note: lightburn keeps in memory a configuration called ttyS0 without it being linked to a machine or a type of config (grbl, etc.) and which cannot be erased.  
system: lubuntu 22.04  
laser : Neje master 2 max A40640 module

Thank you for your answers

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 11:34am UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/2 "2024-03-13T11:34:59Z")

</div>

> [@lauranebzh](#):
>
> “Failed to open port - already in use?”

can you confirm, or send a screenshot of lightburn, that you are selecting the correct com port on the laser panel?

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 11:47am UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/3 "2024-03-13T11:47:23Z")

</div>

![screen01](https://forum.lightburnsoftware.com/uploads/default/original/3X/e/e/ee15ffc869be54657bb7ff2926643e9baf4f33fe.jpeg)  
 ![screen02](https://forum.lightburnsoftware.com/uploads/default/original/3X/4/4/44a542e169435bc2b25fe396dbc62522be15c21c.jpeg)

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 12:23pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/4 "2024-03-13T12:23:34Z")

</div>

in your console/terminal on linux can you type  
With machine plugged in and powered on

lsusb  
and post the export

or  
ls /sys/class/tty/ttyUSB\*

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 12:28pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/5 "2024-03-13T12:28:34Z")

</div>

if laser is connected in usb02 :

```auto
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 007: ID 05e3:0608 Genesys Logic, Inc. Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 7392:a812 Edimax Technology Co., Ltd Edimax AC600 USB
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 046d:c077 Logitech, Inc. M105 Optical Mouse
Bus 001 Device 009: ID 1a86:7523 QinHeng Electronics CH340 serial converter
Bus 001 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

if usb key is connected in usb2 
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 007: ID 05e3:0608 Genesys Logic, Inc. Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 7392:a812 Edimax Technology Co., Ltd Edimax AC600 USB
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 046d:c077 Logitech, Inc. M105 Optical Mouse
Bus 001 Device 010: ID 0781:5581 SanDisk Corp. Ultra
Bus 001 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

```

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 12:35pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/6 "2024-03-13T12:35:10Z")

</div>

Unplug laser and repeat?  
Because i cant see it.

Granted i am not a Linux expert maybe i am missing it

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 12:41pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/7 "2024-03-13T12:41:28Z")

</div>

> [@lauranebzh](#):
>
> `Bus 001 Device 010: ID 0781:5581 SanDisk Corp. Ultra`

if i connected an usbkey in usb2 I see it :

`Bus 001 Device 010: ID 0781:5581 SanDisk Corp. Ultra`

I connected the laser Neje on the same usb2 I dont see it with lsusb. but I verified my usb cable that it’s ok with other material.

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 12:47pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/8 "2024-03-13T12:47:53Z")

</div>

i am really not an expert in linux so we might need some better brains on this

Lets see if others can help  
But from what i can see your linux box is not seeing the laser at all

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 1:01pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/9 "2024-03-13T13:01:43Z")

</div>

yes i verified the usb lightburn connect with the command

```auto
ls /dev/ttyUSB*
/dev/ttyUSB0

```

the ch340 driver is ok.  
if I used in lightburn the grbl-lpc or grbl-m3 in device auto i see in lightburn console : “waiting for connection”  
and if I connect to neje application to the laser the material is recognized and works correctly.

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 1:40pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/10 "2024-03-13T13:40:53Z")

</div>

Neje - specially the latest ones - should be not under M3 or LPC but Top Grlb controller you should do it by hand  
But Lightburn must be able to see it correct too

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 2:01pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/11 "2024-03-13T14:01:08Z")

</div>

yes and in the lightburn test versus, my params was grbl 1.1 by usb mode and the neje laser material was working well…

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 4:19pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/12 "2024-03-13T16:19:26Z")

</div>

> [@lauranebzh](#):
>
> `Bus 001 Device 009: ID 1a86:7523 QinHeng Electronics CH340 serial converter`

if i read my lsusb the laser is here

```auto
Bus 001 Device 009: ID 1a86:7523 QinHeng Electronics CH340 serial converter

```

but not recognized in lightburn 1.5.2

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 4:24pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/13 "2024-03-13T16:24:33Z")

</div>

I cant imagine any reason why your lightburn isnt - now that you enabled license your device  
I sugest you delete your current profile, and add a grbl profile by hand

Then select the correct port, and connect

Remember that on Linux there are special instructions for giving $USER

> sudo adduser $USER dialout && sudo adduser $USER tty

> **[Installation & Setup - LightBurn Documentation](https://docs.lightburnsoftware.com/Installation.html#linux-compatibility)**
>
> Better software for laser cutters.

Reconfirm this

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 4:29pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/14 "2024-03-13T16:29:18Z")

</div>

> [@gilaraujo](#):
>
> cant imagine any reason why your lightburn isnt - now that you enabled license your device  
> I sugest you delete your current profile, and add a grbl profile by hand
> 
> Then select the correct port, and connect
> 
> Remember that on Linux there are special instructions for giving $USER
> 
> > sudo adduser $USER dialout && sudo adduser $USER tty

It’s done.  
and it was a manual configuration that was done. the detection version does not find the neje laser either

I have no more ideas either

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 13, 2024, 4:30pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/15 "2024-03-13T16:30:07Z")

</div>

We would need someone with more experience on linux to help

I cant thikn of anything else

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 5:34pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/16 "2024-03-13T17:34:30Z")

</div>

if i see the file lbset in machine settings folder :  
“{  
“Name”: “GRBL”,  
“Settings”: [  
]  
}”  
is this normal?

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 13, 2024, 8:48pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/17 "2024-03-13T20:48:10Z")

</div>

because i read that ubuntu 22.04 change the mouse driver, i am change usb for the mouse and reboot the pc and lightburn, remake my grbl config

i am seeing this :

"Waiting for connection…

Waiting for connection…

Grbl 1.1f [‘$’ for help]

ok

[VER:1.1f.20180715:]

[OPT:VML,35,254]

Target buffer size found

ok

Homing

ok"

now test if all works well 😉

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 15, 2024, 12:38pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/18 "2024-03-15T12:38:11Z")

</div>

I write a new sujet because I have problem (homing) between lightburn and grbl controller that is not a problem on neje app, or for material reset

---

<div class="post-metadata">

**Author:** ![gilaraujo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/gilaraujo/32/71745_2.png) [@gilaraujo](https://forum.lightburnsoftware.com/u/gilaraujo)\
**Post date:** [March 15, 2024, 12:49pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/19 "2024-03-15T12:49:27Z")

</div>

Homing is Software independent  
This happens at the firmware level

What errors you getting in console?

---

<div class="post-metadata">

**Author:** ![lauranebzh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/l/c57346/32.png) [@lauranebzh](https://forum.lightburnsoftware.com/u/lauranebzh)\
**Post date:** [March 15, 2024, 1:06pm UTC](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886/20 "2024-03-15T13:06:38Z")

</div>

the material now engraves in reverse (in x and y) and I ask to return in home on lightburn, it the machine tries to exceed the y and no stop. but if I press the reset button of the machine it returns correctly to the home of the machine and stop; if I test on neje app, return in home well. note : it is not possible to update the neje firmware on ubuntu (or I have not yet found the solution)

alarm 9 on lightburn

Waiting for connection…

Grbl 1.1f [‘$’ for help]

ok

[VER:1.1f.20180715:]

[OPT:VML,35,254]

Target buffer size found

ok

$0=10

$1=25

$2=0

$3=3

$4=0

$5=0

$6=0

$10=0

$11=0.010

$12=0.002

$13=0

$20=0

$21=0

$22=1

$23=1

$24=250.000

$25=1000.000

$26=250

$27=1.000

$30=1000

$31=0

$32=1

$100=80.000

$101=80.000

$102=80.000

$110=4000.000

$111=4000.000

$112=4000.000

$120=200.000

$121=200.000

$122=200.000

$130=810.000

$131=460.000

$132=150.000

[Next page](https://forum.lightburnsoftware.com/t/neje-laser-not-connected-in-lightburn/132886.md?page=2)
