# No juice in new version

**URL:** <https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398>\
**Category:** LightBurn Software Questions\
**Created:** [March 21, 2019, 5:20pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398 "2019-03-21T17:20:59Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![drdgscott](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/977dab/32.png) [@drdgscott](https://forum.lightburnsoftware.com/u/drdgscott)\
**Post date:** [March 21, 2019, 5:21pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/1 "2019-03-21T17:21:00Z")

</div>

I just installed the new release this morning. When I send an image to the laser, the head moves according to the pattern, the mA meter registers, but the laser doesn’t fire. When I close Lightburn, I get a good test fire. I uninstalled the new release, re-installed the previous version and now it won’t fire, either. Shut down Lightburn and get a good test fire.

I must be missing something simple, but I can’t figure out what it might be. Running Mini Gerbil on a K40, worked like a peach before I installed the new version.

As per réponse to mrfoameruk on 2/13, I checked my $30 and $32 settings and both are as they should be.

Ideas?

Thanks!  
Doug

---

<div class="post-metadata">

**Author:** ![LightBurn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/lightburn/32/75577_2.png) [@LightBurn](https://forum.lightburnsoftware.com/u/LightBurn)\
**Post date:** [March 21, 2019, 6:15pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/2 "2019-03-21T18:15:14Z")

</div>

> [@drdgscott](#):
>
> I checked my $30 and $32 settings and both are as they should be.

Those being? Have you checked the S-Value Max setting in the device settings to make sure that matches the $30 setting?

There’s no magic here - try simple console commands, like this:  
M4 ; Enable the laser  
G0 X0 ; goto X0  
G1 X10 F600 S200 ; cut 10mm in 1 sec  
M5

If that works, then there’s a likely settings issue. You could save the generated GCode from LightBurn to see what’s getting sent.

---

<div class="post-metadata">

**Author:** ![drdgscott](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/977dab/32.png) [@drdgscott](https://forum.lightburnsoftware.com/u/drdgscott)\
**Post date:** [March 21, 2019, 6:33pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/3 "2019-03-21T18:33:31Z")

</div>

$30=1000  
$32=1  
S-value max 1000

I ran M4, “light instruction” indicator lights up  
G0 X0 carriage moves  
G1 X10 F600 S200, carriage moves, laser does not fire  
M5 “light instruction” indicator turns off.

Grrr.

---

<div class="post-metadata">

**Author:** ![drdgscott](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/977dab/32.png) [@drdgscott](https://forum.lightburnsoftware.com/u/drdgscott)\
**Post date:** [March 21, 2019, 6:45pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/4 "2019-03-21T18:45:30Z")

</div>

This is the code for my little program:  
\<Idle|MPos:0.000,0.000,0.000,0.000,0.000|Bf:15,254|FS:0,0|WCO:0.000,0.000,0.000,0.000,0.000\>

ok

Starting stream

Stream completed in 0:00

\<Idle|MPos:28.000,35.000,0.000,0.000,0.000|Bf:15,254|FS:0,0|Ov:100,100,100|A:C\>

ok

Starting stream

[MSG:Pgm End

Stream completed in 0:35

---

<div class="post-metadata">

**Author:** ![LightBurn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/lightburn/32/75577_2.png) [@LightBurn](https://forum.lightburnsoftware.com/u/LightBurn)\
**Post date:** [March 21, 2019, 8:08pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/5 "2019-03-21T20:08:06Z")

</div>

I would check with AwesomeTech - if there’s an indicator on the board that’s lighting when you use M4, it means that LightBurn is working as intended, and there’s possibly a loose wire or other board issue that coincidentally happened when you updated.

---

<div class="post-metadata">

**Author:** ![drdgscott](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/977dab/32.png) [@drdgscott](https://forum.lightburnsoftware.com/u/drdgscott)\
**Post date:** [March 21, 2019, 8:24pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/6 "2019-03-21T20:24:21Z")

</div>

Thanks. I’ll head over there.

---

<div class="post-metadata">

**Author:** ![raykholo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/raykholo/32/2170_2.png) [@raykholo](https://forum.lightburnsoftware.com/u/raykholo)\
**Post date:** [May 7, 2019, 8:23pm UTC](https://forum.lightburnsoftware.com/t/no-juice-in-new-version/2398/7 "2019-05-07T20:23:54Z")

</div>

Closed on May 7, 2019, 8:23pm UTC


