O so I lately I’ve had an issue that happens at different times… While burning a 3’ inch emblem on soft pine wood, the print job stops, freezes and in some cases starts to print a double image.
I have literally tried everything from restarting my system, resetting the Ortur, I have checked and rechecked the power settings, USB cable and changed out the power unit.
No matter what it seems that regardless of the type of laser job it continues to happen. The last few times the job stopped, I checked the console window and all of the G1 Y- settings appeared.
My Settings…
$1
error:3
Grbl ‘$’ system command was not recognized or supported.
$$
$0=5.0 $1=100 $2=0
$3=3 $4=7 $5=7
$6=1 $10=2047 $11=0.050
$12=0.002 $13=0 $14=6
$15=0 $16=1 $17=4
$18=0 $19=0 $20=0
$21=1 $22=1 $23=7
$24=600.000 $25=3000.000 $26=100
$27=3.000 $28=0.100 $29=0.0
$30=1000. $31=0. $32=1
$33=1000.000 $34=0.000 $35=0.000
$36=100.000 $37=0 $39=1
$40=1 $41=0 $42=1
$43=1 $44=3 $45=0
$46=0 $56=1.000 $57=1800.000
$58=405.000 $59=6000.000 $60=0
$61=0 $62=0 $63=3
$64=1 $65=0 $100=80.000
$101=80.000 $102=2124.000 $110=10200.000
$111=10200.000 $112=600.000 $120=2200.000
$121=1800.000 $122=200.000 $130=390.000
$131=410.000 $132=100.000 $259=0
$260=70 $261=0 $262=400
$263=30 $264=0 $265=50
$266=100 $267=0 $268=0
$269=0 $270=5120
$#
[G54:0.000,0.000,0.000]
[G55:0.000,0.000,0.000]
[G56:0.000,0.000,0.000]
[G57:0.000,0.000,0.000]
[G58:0.000,0.000,0.000]
[G59:0.000,0.000,0.000]
[G59.1:0.000,0.000,0.000]
[G59.2:0.000,0.000,0.000]
[G59.3:0.000,0.000,0.000]
[G28:0.000,0.000,0.000]
[G30:0.000,0.000,0.000]
[G59.6:0.000,0.000,0.000]
[G92:0.000,0.000,0.000]
[HOME:0.000,0.000,0.000:0]
[TLO:0.000]
$I
[ORIGIN: China]
[PRODUCER: ORTUR]
[AUTHOR: ORTUR]
[MODEL: Ortur Laser Master 2 S2]
[OLF: 187]
[OLH: OLM_ESP_PRO_V1.2]
[SN: 25EB0D195107F5AD0FD585321C04F55A]
[OLM:GENERAL]
[DATE:17:28:09 - Dec 15 2021]
[VER:1.1f(ESP32).20210403:]
[OPT:VNMZHSL,35,7680,3]
Target buffer size found
[PRB:0.000,0.000,0.000:0]