Ortur won't start up

LightBurn Software Questions [OFFICIAL]
#1

Waiting for connection…

Waiting for connection…

ALARM:9

Homing fail. Could not find limit switch within search distance. Defined as 1.5 * max_travel on search and 5 * pulloff on locate phases.

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:0]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

[MSG:’$H’|’$X’ to unlock]

[MSG:Caution: Unlocked]

ok

Homing

ALARM:9

Homing fail. Could not find limit switch within search distance. Defined as 1.5 * max_travel on search and 5 * pulloff on locate phases.

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

ok

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:2]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

[MSG:’$H’|’$X’ to unlock]

[MSG:Caution: Unlocked]

ok

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:3]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:3]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:3]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:3]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 188.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG: Flame detector active,Ambient infrared value:3]

Grbl 1.1f [’$’ for help]

[MSG:Power Supply Problem:0V.Check TroubleShooting Section in User Manual.]

#2

Do you have your power supply plugged into the controller? Is the power supply in working order? Are you getting power at the wall?

If you disconnect USB, are you able to power on the laser? Do the stepper motors attempt to home?

#3

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.