# Rotary does not turn

**URL:** <https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994>\
**Category:** WeCreat\
**Tags:** rotary\
**Created:** [May 22, 2026, 11:00pm UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994 "2026-05-22T23:00:43Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![mlayman](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/m/45deac/32.png) [@mlayman](https://forum.lightburnsoftware.com/u/mlayman)\
**Post date:** [May 22, 2026, 11:00pm UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994/1 "2026-05-22T23:00:43Z")

</div>

First day I tried my rotary it worked (although the y axis was stretched). Since then the rotary does not turn. When I frame a project the laser head moves on the x axis but the rotary does not rotate on the y axis.

I have rebooted everything and reinstalled the rotary hardware, but no response.

---

<div class="post-metadata">

**Author:** ![mlayman](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/m/45deac/32.png) [@mlayman](https://forum.lightburnsoftware.com/u/mlayman)\
**Post date:** [May 23, 2026, 5:39pm UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994/2 "2026-05-23T17:39:10Z")

</div>

\*\*Rotary works fine with WeCreat Makeit software, but there is no rotation in Lightburn software. Connections and wiring are good but I am not getting the right commands from Lightburn(?)  
\*\*

---

<div class="post-metadata">

**Author:** ![MikeyH](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/m/43a26b/32.png) [@MikeyH](https://forum.lightburnsoftware.com/u/MikeyH)\
**Post date:** [May 24, 2026, 6:50pm UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994/3 "2026-05-24T18:50:13Z")

</div>

> [@mlayman](#):
>
> there is no rotation in Lightburn software

Is the correct axis selected in the Rotary Setup window/

> [@mlayman](#):
>
> First day I tried my rotary it worked

Are you sure you hooked it up properly? To the controller, it is just another stepper motor on the Yaxis.

---

<div class="post-metadata">

**Author:** ![mlayman](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/m/45deac/32.png) [@mlayman](https://forum.lightburnsoftware.com/u/mlayman)\
**Post date:** [May 24, 2026, 11:59pm UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994/4 "2026-05-24T23:59:54Z")

</div>

Yes, I am sure it is properly installed. It works fine with the WeCreat Makeit software.

It is also set up in the rotary window of LightBurn software correctly. It should work with the an axis option, although I tested all of the options and none of them worked.

---

<div class="post-metadata">

**Author:** ![MikeyH](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/m/43a26b/32.png) [@MikeyH](https://forum.lightburnsoftware.com/u/MikeyH)\
**Post date:** [May 25, 2026, 12:44am UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994/5 "2026-05-25T00:44:42Z")

</div>

Not doubting your word. What interests me is that it worked the first day. That establishes that it will work with Lightburn. What we have to figure out what got changed between day 1 and day 2.

Maybe you could create a second Device new. If you have a .lbdev file, then load that. Maybe a fresh start will help.

I am sure it is impossible to remember everything you did after the end of day 1.

---

<div class="post-metadata">

**Author:** ![parsec](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/parsec/32/118933_2.png) [@parsec](https://forum.lightburnsoftware.com/u/parsec)\
**Post date:** [May 25, 2026, 4:07am UTC](https://forum.lightburnsoftware.com/t/rotary-does-not-turn/189994/6 "2026-05-25T04:07:47Z")

</div>

I’m on mobile and unable to check.  
If you’re using a CustomGCode device change here from A to Y.

 ![image](https://forum.lightburnsoftware.com/uploads/default/original/3X/2/1/2193b5f4349b591f64f6fe8543b2ee05c35b4648.jpeg)
