# Sculpfun S9 no longer connects/responds

**URL:** <https://forum.lightburnsoftware.com/t/sculpfun-s9-no-longer-connects-responds/80222>\
**Category:** LightBurn Hardware Compatibility\
**Created:** [October 28, 2022, 9:29am UTC](https://forum.lightburnsoftware.com/t/sculpfun-s9-no-longer-connects-responds/80222 "2022-10-28T09:29:09Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![devissjh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/22d042/32.png) [@devissjh](https://forum.lightburnsoftware.com/u/devissjh)\
**Post date:** [October 28, 2022, 9:29am UTC](https://forum.lightburnsoftware.com/t/sculpfun-s9-no-longer-connects-responds/80222/1 "2022-10-28T09:29:09Z")

</div>

My Sculpfun S9 was working great then all of sudden it has stopped connecting/responding. I have checked settings, reinstalled drivers and software and changed USB cables all with no result. When starting lightburn there are all these weird symbols in console window and the laser window shows the unit is constantly busy but nothing happens. See screen shot. Anyone have any ideas on what went wrong and how to fix?

 ![image](https://forum.lightburnsoftware.com/uploads/default/original/3X/2/8/2839eea3325060ee0261da46f831704e0062aca8.png)

---

<div class="post-metadata">

**Author:** ![misken](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/misken/32/47593_2.png) [@misken](https://forum.lightburnsoftware.com/u/misken)\
**Post date:** [October 28, 2022, 6:00pm UTC](https://forum.lightburnsoftware.com/t/sculpfun-s9-no-longer-connects-responds/80222/2 "2022-10-28T18:00:36Z")

</div>

These symbols indicate a communication problem with the laser. Usually, this is caused by a bad USB connection or electrical interference while connected. Make sure you remove all these factors. (A few more are listed here: [FAQ - Diode Laser Wiki](https://wiki.the-iskens.com/documentation/frequently-asked-questions/))

If there are still problems, I recommend updating the firmware, I already had some cases where this was required to get stable operation back. A guide is here: [https://wiki.the-iskens.com/documentation/firmware-update/](https://wiki.the-iskens.com/documentation/firmware-update/)

---

<div class="post-metadata">

**Author:** ![devissjh](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/22d042/32.png) [@devissjh](https://forum.lightburnsoftware.com/u/devissjh)\
**Post date:** [October 28, 2022, 8:33pm UTC](https://forum.lightburnsoftware.com/t/sculpfun-s9-no-longer-connects-responds/80222/3 "2022-10-28T20:33:02Z")

</div>

Thanks. Flashing the bios did the trick. unit is running again.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [November 27, 2022, 8:33pm UTC](https://forum.lightburnsoftware.com/t/sculpfun-s9-no-longer-connects-responds/80222/4 "2022-11-27T20:33:35Z")

</div>

Closed on November 27, 2022, 8:33pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
