# Show me your dual source setups

**URL:** <https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257>\
**Category:** Community Laser Talk\
**Tags:** ruida, diode\
**Created:** [September 22, 2023, 2:34pm UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257 "2023-09-22T14:34:29Z")\
**Posts on this page:** 12\
**Page:** 1

<div class="post-metadata">

**Author:** ![julienrl](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/c57346/32.png) [@julienrl](https://forum.lightburnsoftware.com/u/julienrl)\
**Post date:** [September 22, 2023, 2:34pm UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/1 "2023-09-22T14:34:29Z")

</div>

I’m thinking of adding a diode source to my co2 laser. I have a rdc6445g so I should be able to make that work (and if not I’d put in some hardware switch anyways). I’m more interested in seeing how people have mechanically attached both sources.

Thanks!

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [September 24, 2023, 12:28am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/2 "2023-09-24T00:28:50Z")

</div>

A few people have attempted this … The basic Chinese laser is a general description… how it’s actually built is up the manufacturer, meaning there is no real standard on how these are mounted.

I replaced the head and drive on my OMTech China Blue and the laser module on a couple of my CNC3018 types… Both required me to design some type of mount.

* * *

A Ruida doesn’t use/generate signals for a dpssl type.

The lps requires a pwm signal to set it’s current, and an L-On (laser enable) to instruct the lps to lase the tube.

On a Ruida the pwm is generated continuously when the machine is running a layer, it does not control when the machine lases only the current setting of the lps.

You’d have to implement some type of _ **logic gate** _ to allow for a proper signal to the pwm input of the dpssl module. Pass the pwm signal only when the L-On line goes low…

Make sense?

😸

---

<div class="post-metadata">

**Author:** ![julienrl](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/c57346/32.png) [@julienrl](https://forum.lightburnsoftware.com/u/julienrl)\
**Post date:** [September 24, 2023, 12:37am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/3 "2023-09-24T00:37:26Z")

</div>

I had read elsewhere that the ruida can run in the correct mode for the diode, just not both co2 and diode at the same time. I’d have to change profile each time. Workshop real-estate is my real limiter so compromises in building this kind of mash up is worth it for me.

And yes, I’ll absolutely have to make a bracket! Lol

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [September 24, 2023, 1:24am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/4 "2023-09-24T01:24:27Z")

</div>

There is no option to drive a regular dpssl from it without some kind of external logic. If you can find the source where they claim this, I’d love to read it.

There is no doubt you can do it, it’s just not a simple option change… PWM is generated throughout layer execution… you can’t change that… so you need external logic to generate the proper signal.

Although the Ruida allows you to invert the L-On (laser on) that’s the scope of what you can change with it’s signals. And that really isn’t of much help in this situation.

Good luck

😸

---

<div class="post-metadata">

**Author:** ![berainlb](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/b/85f322/32.png) [@berainlb](https://forum.lightburnsoftware.com/u/berainlb)\
**Post date:** [September 24, 2023, 1:48am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/5 "2023-09-24T01:48:48Z")

</div>

> [@jkwilborn](#):
>
> PWM is generated throughout layer execution… you can’t change that… so you need external logic to generate the proper signal.

Wouldn’t the PWM generated by the controller still match the power proportions specified either during a cut, engrave, or traversal?

A diode laser would only need the presence of a non-zero PWM to fire in which case L-On becomes irrelevant.

One note is that the laser type likely needs to be configured as RF for this to work properly. L-On is disabled when configured as RF. I assume no-preignition pulse would be required.

Also, I assume that power is being supplied externally although a 24V laser module would probably be fine being fed by the stepper power supply.

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [September 24, 2023, 2:23am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/6 "2023-09-24T02:23:06Z")

</div>

I think we have some miscommunication…

The dpssl module controls the laser with a single line. This is the pwm, when it goes high the module turns on the laser.

DSP controllers use two lines. IN on the lps determines the output current limit for lps and is controlled via the pwm generated by the controller…

The other line is laser enable, this output tells the lps when to lase the tube.

On a dpssl type or most of the grbl type controllers there is only one control line…pwm…

You have to get _ **pwm** _ and _ **laser enable** _ into one control line …

You’re not the first, so don’t make it more complicated than need be. RF excited lasers are quite a different animal. Neither co2 nor rf work like the dpssl interface.

Follow?

😸

---

<div class="post-metadata">

**Author:** ![berainlb](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/b/85f322/32.png) [@berainlb](https://forum.lightburnsoftware.com/u/berainlb)\
**Post date:** [September 24, 2023, 2:28am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/7 "2023-09-24T02:28:49Z")

</div>

A few things to consider:

1. I don’t think OP is talking about DPSSL lasers, sounds to me more like a commodity diode laser.
2. 

> [@jkwilborn](#):
>
> DSP controllers use two lines. IN on the lps determines the output current limit for lps and is controlled via the pwm generated by the controller…
> 
> The other line is laser enable, this output tells the lps when to lase the tube.

I don’t have a problem with these statements.

1. 

> [@jkwilborn](#):
>
> You have to get _ **pwm** _ and _ **laser enable** _ into one control line …

This is also fine with a nuance. It’s simply the presence of a non-zero PWM that signals laser on. In other words, the diode laser will fire for all non-zero duty cycles of PWM.

1. 

> [@jkwilborn](#):
>
> RF excited lasers are quite a different animal.

RF works differently to glass tube lasers. L-On is disabled for RF function and only provides PWM which is why it may be analogous enough to diode laser function for this to work properly.

The part I’m not certain about is whether or not PWM goes to zero during traversal moves on the Ruida. I assume it would need to if L-On is disabled during RF function.

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [September 24, 2023, 2:48am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/8 "2023-09-24T02:48:38Z")

</div>

> [@berainlb](#):
>
> not certain about is whether or not PWM goes to zero during traversal moves

Interesting idea… I have not gone down this path with the Ruida… there’s probably lots of paths I haven’t gone down…

Looking at the manual they don’t say anything about the l-on when associated with rf machines.

I would have to think the pwm would have to _ **go to ground** _ or it would be lasing.

Apparently, I’ve been told they can lase at very low %… I could never afford one, but once I stood next to one and found out how deafening it was… not sure I’d really use it.

 ![image](https://forum.lightburnsoftware.com/uploads/default/original/3X/b/9/b90fa97212067a927657cdb611ca7d6eff85aa00.jpeg)

> [@berainlb](#):
>
> non-zero PWM that signals laser on

The diode or tube/lps?

* * *

If I get off my bottom, I’ll change mine to RF and hang the scope off it and see what it does with the pwm and how L-On reacts…

😸

---

<div class="post-metadata">

**Author:** ![berainlb](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/b/85f322/32.png) [@berainlb](https://forum.lightburnsoftware.com/u/berainlb)\
**Post date:** [September 24, 2023, 2:59am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/9 "2023-09-24T02:59:25Z")

</div>

> [@jkwilborn](#):
>
> Looking at the manual they don’t say anything about the l-on when associated with rf machines.

Take a look at this. This is from the manual for the 6445.

 ![image](https://forum.lightburnsoftware.com/uploads/default/original/3X/d/4/d487f6ba527ccfd5c404cae9bc7d17941c94e807.png)

> [@jkwilborn](#):
>
> I would have to think the pwm would have to _ **go to ground** _ or it would be lasing.

This makes sense to me.

> [@jkwilborn](#):
>
> The diode or tube/lps?

Not tube/lps. The signaling function of diode laser module.

> [@jkwilborn](#):
>
> If I get off my bottom, I’ll change mine to RF and hang the scope off it and see what it does with the pwm and how L-On reacts…

Nothing like some practical footwork.

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [September 24, 2023, 3:18am UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/10 "2023-09-24T03:18:25Z")

</div>

I know it states that, as long as it doesn’t become _ **unpredictable** _…

* * *

Some simple tests should show us what it’s doing…

I’ll try some slow speed engraving of a few circles so it will have to turn off to transverse to another object… should be apparent.

😸

---

<div class="post-metadata">

**Author:** ![julienrl](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/j/c57346/32.png) [@julienrl](https://forum.lightburnsoftware.com/u/julienrl)\
**Post date:** [September 24, 2023, 1:06pm UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/11 "2023-09-24T13:06:29Z")

</div>

This has become way more technical and interesting than I’d imagined 😁 honestly some of it is over my head, but that’s what Google is for!

---

<div class="post-metadata">

**Author:** ![jkwilborn](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/jkwilborn/32/63089_2.png) [@jkwilborn](https://forum.lightburnsoftware.com/u/jkwilborn)\
**Post date:** [September 24, 2023, 7:43pm UTC](https://forum.lightburnsoftware.com/t/show-me-your-dual-source-setups/111257/12 "2023-09-24T19:43:57Z")

</div>

Might check out this thread.

Here is what I found out, thanks to @berainlb suggestion…

> [@Relation pwm generated with different min/max controller setting](https://forum.lightburnsoftware.com/t/relation-pwm-generated-with-different-min-max-controller-setting/111441/1):
>
> The other part of this story was what happens to L-On when in this mode. I watched it on a multimeter and saw that L-On remains low… I actually expect a high state as this would allow the tube to lase if you mistakenly had it set to rf…

😸
