# Slowing down traverse movements between cuts on OMTech K40

**URL:** <https://forum.lightburnsoftware.com/t/slowing-down-traverse-movements-between-cuts-on-omtech-k40/142591>\
**Category:** LightBurn Software Questions\
**Tags:** smoothieware, travel-vs-engrave, k40, omtech, rotary\
**Created:** [June 26, 2024, 8:42pm UTC](https://forum.lightburnsoftware.com/t/slowing-down-traverse-movements-between-cuts-on-omtech-k40/142591 "2024-06-26T20:42:11Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![kmcvay24](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/k/7c8e57/32.png) [@kmcvay24](https://forum.lightburnsoftware.com/u/kmcvay24)\
**Post date:** [June 26, 2024, 8:42pm UTC](https://forum.lightburnsoftware.com/t/slowing-down-traverse-movements-between-cuts-on-omtech-k40/142591/1 "2024-06-26T20:42:12Z")

</div>

I am trying to find a way to slow down the movements of my K40 laser when the head is moving to cuts and between cuts. I got a new rotary, and the movement speeds are so fast that it’s causing the cup to jump and the laser to cut in the wrong spot. I have the upgraded Smoothie board on my K40. I have tried turning “Fast Whitespace Scan” off in the machine settings, and I have tried leaving it on and lowering it to 5 mm/sec. No difference. Am I missing a setting somewhere? Is there a way to edit the basic gcode so that it defaults to slower speeds? Thanks for any advice/help!

---

<div class="post-metadata">

**Author:** ![parsec](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/parsec/32/118933_2.png) [@parsec](https://forum.lightburnsoftware.com/u/parsec)\
**Post date:** [June 26, 2024, 11:34pm UTC](https://forum.lightburnsoftware.com/t/slowing-down-traverse-movements-between-cuts-on-omtech-k40/142591/2 "2024-06-26T23:34:37Z")

</div>

Likely you have to edit your “configxxx.txt” so read the following threads:

> [@OMtech K40 Laser Utilizing the K40+ Smoothieboard Upgrade Processor Card Adding Rotary Problem to E-Axis Solved](https://forum.lightburnsoftware.com/t/omtech-k40-laser-utilizing-the-k40-smoothieboard-upgrade-processor-card-adding-rotary-problem-to-e-axis-solved/108949/6):
>
> Another question, in your config file, what steps per mm are you using? If you are using 19 per Amazon config, how did you calculate that? I have a NEMA 17 stepping motor.

> [@Console commands](https://forum.lightburnsoftware.com/t/console-commands/105365):
>
> trying to find list of commands, and a primer to understand the config file (mostly ports & pins) Primarily adding control to air assist and exhaust blower on an OMtech K40+ (smoothie) board with Lightburn on a basic K40

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [July 26, 2024, 11:35pm UTC](https://forum.lightburnsoftware.com/t/slowing-down-traverse-movements-between-cuts-on-omtech-k40/142591/3 "2024-07-26T23:35:21Z")

</div>

Closed on July 26, 2024, 11:35pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
