# Why do 2 lenses of the same diameter and focal length behave VERY differently

**URL:** <https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006>\
**Category:** LightBurn Hardware Compatibility\
**Created:** [August 26, 2020, 1:17am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006 "2020-08-26T01:17:55Z")\
**Posts on this page:** 18\
**Page:** 1

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 26, 2020, 1:17am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/1 "2020-08-26T01:17:55Z")

</div>

Question about replacement lenses … The Laguna owners manual for the PL12|20 CO2 40Watt Laser is inconsistent about specifying the type of lens needed. In 2 places the manual says the lens is 20mm diameter 50.8mm focal length. However, in the specifications chart, it says 20mm diameter 25.4mm focal length. The 25.4mm focal length is 1 inch. The lens is up in the adjustable head tube much more than an inch. So the 25.4mm cannot be right. Right?  
I got a replacement lens that’s 20mm diameter 50.8mm focal length. It behaves totally different than the original lens. At the same focal spacing (7mm) and power & speed settings as the original lens, it produces a wide burn mark and a wider beveled cut. It obviously has a different focal length than the origin lens. If both lenses are 20mm diameter 50.8mm focal length, why would this be? What am I missing?

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 1:24am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/2 "2020-08-26T01:24:45Z")

</div>

Two things come to mind. Either your original lens was a 1.5" / 38.1mm focal length, or you flipped the lens over.

The focal length changes slightly depending on if you set your lens curve up or curve down, and the shorter the focal length, the more that matters. I run strickly curve up for my cutting, gets me as close to the nozzle for air assist as I can short of adding some spacers to the nozzle thread.

Also, that 1" may be to the nozzle tip, not the actual focal point. We all know how excellent the Chinese to English translations are… Do a ramp test to see what your actual focal point is using 1.5" and 2" as your starting point.

---

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 26, 2020, 1:39am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/3 "2020-08-26T01:39:47Z")

</div>

I have the domed side up on both the original and replacement lenses. The original lens performs flawlessly. Maybe the owners manual is wrong all together and the original lens is 20mm diameter with 38.1mm focal length?

I’ve also noticed that all the 20mm diameter 50.8mm focal length lenses I’ve found seem to be meniscus (i.e. concave on one side and convex on the other side). The 20mm diameter with 38.1mm focal length lens I’ve found is convex. Amazon says it has free returns, do you think this would be worth a shot?

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 1:57am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/4 "2020-08-26T01:57:46Z")

</div>

If you have the tube length, or can add an extension to get the tube length, I’d keep the 2". The longer the focal length, the better you cut thicker material.

EXAMPLE: With my original set up and a 1.5" lens, I was cutting 3mm Premium MDF easily, and barely cutting 6mm. Switch to a 2" and the 6mm is cutting okay, but the 9mm is a bit iffy. If I get the new mount in place for the 4" lens, the 9mm will be no problem, and I may take a shot at 12mm.

---

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 26, 2020, 2:22am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/5 "2020-08-26T02:22:27Z")

</div>

Nice to know. Thanks for your insights.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 2:27am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/6 "2020-08-26T02:27:42Z")

</div>

Quite often the factory set up will handle both a 1.5" and a 2" lens. Usually the 1.5" will sit in a notch in the top of the nozzle, and the 2" will be held up in the lens tube by a retaining ring.

The zinger comes in when you determine if you have an engraving set up or a cutting set up. If you have an engraving set up and a 2", you can get a bit better performance by dropping a 1.5" lens in to get closer to your work and drilling out the air elbow fitting. It won’t be a true cutting set up, but it’s better than an basic engraving set up.

Trying to cut with an engraving set up puts you at a rough 40% disadvantage.

---

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 26, 2020, 2:30am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/7 "2020-08-26T02:30:57Z")

</div>

My lens is up in the tube with a retaining ring

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 2:38am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/8 "2020-08-26T02:38:57Z")

</div>

That’s about as long as you can go with your stock set up. Is that with a 1.5" or a 2"?

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 2:39am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/9 "2020-08-26T02:39:32Z")

</div>

Better question, how much distance do you have lens to nozzle tip?

---

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 26, 2020, 4:46pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/10 "2020-08-26T16:46:07Z")

</div>

2-1/8 Inches from lens to tip of nozzle. I guessing a 1 inch or 1-1/2 inch focal length lens would not work?

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 4:58pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/11 "2020-08-26T16:58:18Z")

</div>

If you put it all the way up, you are going to need a 2.5" lens. On my first set up, the lens sat on top of the nozzle with the retaining ring and an o-ring in the tube above it to hold it all together. If you can do that, then I would imagine you are in the 2" or maybe 1.5" territory depending.

If you have the room, you can space the lens down with o-rings and such.

---

<div class="post-metadata">

**Author:** ![Stroonzo](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/stroonzo/32/8293_2.png) [@Stroonzo](https://forum.lightburnsoftware.com/u/Stroonzo)\
**Post date:** [August 26, 2020, 5:01pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/12 "2020-08-26T17:01:34Z")

</div>

I use and keep a 4" lens in my machine for everything. The engraving is excellent. The cutting is amazing. Best tip I can give you is to stick with Two - Six lenses (II-VI).

> [@What do these designations mean on a lens?](https://forum.lightburnsoftware.com/t/what-do-these-designations-mean-on-a-lens/13966):
>
> What does CX/AR(LP) mean? Same for CC.

> [@Which lens to use](https://forum.lightburnsoftware.com/t/which-lens-to-use/19758/5):
>
> You have a tiny spot for photo engraving. the ‘sweet spot’ for cutting is a matter of ‘depth’. I’ll give you my laymen explanation, and you can cuss me out later. You have the perfect ‘spot’, but if that was the only place you could cut, the only thing you could cut with a laser would be tissue paper. While the ‘spot’ is the hottest, you have X amount of distance above and below the ‘spot’ where the laser still has the energy to cut. That energy along with power ( Wattage ) and good air assist …

> [@4” lens issues. Will not cut though material](https://forum.lightburnsoftware.com/t/4-lens-issues-will-not-cut-though-material/15313):
>
> Hello. Im new to the site. I have a Nova 35 with a 100 watt laser tube. I’m having trouble getting the 4” lens to work. I can’t get a clean cut and the laser will not cut though material. I installed the larger air cone, increased the air flow, tried different focal lengths for 7mm to 13 mm. I have no issues with the 2” lens and the HR lens. Has anyone else had success with this lens cutting thicker material ? Thanks Richard

---

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 26, 2020, 5:37pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/13 "2020-08-26T17:37:07Z")

</div>

Thanks … I’ve just ordered a 20mm Dia. 63.5mm Focal Length lens (2-1/2"). I’ll see if that does the trick. The owners manual is probably all wrong about the lens … if the distance from the lens to the tip of the nozzle is 2-1/8" a 2" or 1" lens would focus before it made it out of the tube.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 26, 2020, 7:55pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/14 "2020-08-26T19:55:10Z")

</div>

Next thing, have you determined of you have an engraving set up or a cutting set up?

---

<div class="post-metadata">

**Author:** ![Bonjour](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/bonjour/32/711_2.png) [@Bonjour](https://forum.lightburnsoftware.com/u/Bonjour)\
**Post date:** [August 27, 2020, 12:48am UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/15 "2020-08-27T00:48:10Z")

</div>

> [@Stroonzo](#):
>
> I use and keep a 4" lens in my machine for everything. The engraving is excellent. The cutting is amazing. Best tip I can give you is to stick with Two - Six lenses (II-VI).
> 
> [What do these designations mean on a lens?](https://forum.lightburnsoftware.com/t/what-do-these-designations-mean-on-a-lens/13966)
> 
> [Which lens to use - #5 by Dave01](https://forum.lightburnsoftware.com/t/which-lens-to-use/19758/5)
> 
> [4” lens issues. Will not cut though material](https://forum.lightburnsoftware.com/t/4-lens-issues-will-not-cut-though-material/15313)

What Jeff said. II-IV are great. Personally I use Ronar-Smith lenses from Singapore, but that’s because they have been my geo for more than ten years.

> **[About CO2 Laser Optics: CO2 Laser Lenses & CO2 Laser Mirrors](https://wavelength-oe.com/articles/co2-laser-optics/)**
>
> CO2 lasers have become a cornerstone technology in numerous industries and it relies on quality CO2 laser optics like CO2 laser lenses and CO2 laser mirrors.

I use a 3" for everything, but have spare tubes with 2", and 4" lenses, should I need them.

99% of Chinese lasers come with a 2" lens.

---

<div class="post-metadata">

**Author:** ![Aggie79](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/a/3be4f8/32.png) [@Aggie79](https://forum.lightburnsoftware.com/u/Aggie79)\
**Post date:** [August 29, 2020, 4:28pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/16 "2020-08-29T16:28:27Z")

</div>

Thanks Dave … The 20mm Dia. 63.5mm Focal Length lens (2-1/2") works great and matches the performance of my original lens. I’m cutting and engraving with no issues. The owners’ manual is totally wrong about the lens specs.

---

<div class="post-metadata">

**Author:** ![Dave01](https://forum.lightburnsoftware.com/letter_avatar_proxy/v4/letter/d/3d9bf3/32.png) [@Dave01](https://forum.lightburnsoftware.com/u/Dave01)\
**Post date:** [August 29, 2020, 5:55pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/17 "2020-08-29T17:55:16Z")

</div>

Glad to hear you have that part figured out. Have you determined of you have an engraving or cutting set up? I have [pics](https://drive.google.com/drive/folders/1LZCZulbJ9a-00VZoR4JLNN7JKcqX-vHh?usp=sharing) of the nozzle and air elbow differences.

---

<div class="post-metadata">

**Author:** ![system](https://forum.lightburnsoftware.com/user_avatar/forum.lightburnsoftware.com/system/32/64335_2.png) [@system](https://forum.lightburnsoftware.com/u/system)\
**Post date:** [September 28, 2020, 5:55pm UTC](https://forum.lightburnsoftware.com/t/why-do-2-lenses-of-the-same-diameter-and-focal-length-behave-very-differently/21006/18 "2020-09-28T17:55:19Z")

</div>

Closed on September 28, 2020, 5:55pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
