# \#bjjcz-lite

**URL:** https://forum.lightburnsoftware.com/tag/bjjcz-lite/131.md

[Latest](https://forum.lightburnsoftware.com/latest.md) · [Categories](https://forum.lightburnsoftware.com/categories.md) · [Tags](https://forum.lightburnsoftware.com/tags.md)

---

## [Maximum range of working area for rotary working mode (or linear?)](https://forum.lightburnsoftware.com/t/maximum-range-of-working-area-for-rotary-working-mode-or-linear/180007)

<div class="topic-metadata">

**Author:** [@rsx2007](https://forum.lightburnsoftware.com/u/rsx2007)\
**Replies:** 72\
**Last updated:** [November 12, 2025, 10:08pm UTC](https://forum.lightburnsoftware.com/t/maximum-range-of-working-area-for-rotary-working-mode-or-linear/180007 "2025-11-12T22:08:26Z")

</div>

Greetings! We are trying to move away from EZCad and test working with Lightburn, but we cannot create the same workspace as in EZCad. At the moment, we have a working solution in Lightburn that can perform marking in …

---

## [Problem Lightburn for Fiber Laser JPT 30LP](https://forum.lightburnsoftware.com/t/problem-lightburn-for-fiber-laser-jpt-30lp/72421)

<div class="topic-metadata">

**Author:** [@Stas](https://forum.lightburnsoftware.com/u/Stas)\
**Replies:** 16\
**Last updated:** [September 13, 2022, 3:01pm UTC](https://forum.lightburnsoftware.com/t/problem-lightburn-for-fiber-laser-jpt-30lp/72421 "2022-09-13T15:01:03Z")

</div>

Hi. Installed Lightburn and drivers. Lightburn found my laser and identified it as “JCZFiber (unknown)” mainboard bjjcz-clone. choose Fiber Type = JPT and my laser began to move from the “busy” state to the “disconnect…

---

## [Frustrated and ready to ship it all back](https://forum.lightburnsoftware.com/t/frustrated-and-ready-to-ship-it-all-back/71911)

<div class="topic-metadata">

**Author:** [@bordertown\_blades](https://forum.lightburnsoftware.com/u/bordertown_blades)\
**Replies:** 4\
**Last updated:** [July 21, 2022, 8:38pm UTC](https://forum.lightburnsoftware.com/t/frustrated-and-ready-to-ship-it-all-back/71911 "2022-07-21T20:38:08Z")

</div>

I bought an OMTech 30w fiber laser with Galvo laser and the Lightburn software to run on a brand new Mac M1 (Monterey). I have spent the past week and a half watching videos and working with OMTech support for many many …

---

## [Lightburn for fiber EZCAD](https://forum.lightburnsoftware.com/t/lightburn-for-fiber-ezcad/64778)

<div class="topic-metadata">

**Author:** [@EgbertNorth](https://forum.lightburnsoftware.com/u/EgbertNorth)\
**Replies:** 2\
**Last updated:** [April 13, 2022, 3:21am UTC](https://forum.lightburnsoftware.com/t/lightburn-for-fiber-ezcad/64778 "2022-04-13T03:21:34Z")

</div>

Hello everyone, everyone knows that Lightburn is about to replace EZCAD, does anyone know if Lightburn only supports BJJCZ 2nd generation standard cards or can also be used on BJJCZ 2nd generation Lite cards.