|
Strobing and losing focus during line cutting with a Gweike Galvo
|
|
4
|
100
|
March 27, 2025
|
|
Galvo fibre laser loss of power
|
|
6
|
164
|
February 22, 2025
|
|
Fiber 70 lens engraving wrong size after calibration
|
|
1
|
55
|
March 1, 2025
|
|
My Gweike G2 50W does only fire with the red diode laser and not the fiber
|
|
6
|
712
|
February 20, 2025
|
|
I have an problem with fill mode with my fiber laser
|
|
21
|
422
|
February 12, 2025
|
|
Engraved unpainted travel mug
|
|
19
|
775
|
January 11, 2025
|
|
Lightburn does not recognise my galvo laser
|
|
4
|
241
|
February 1, 2025
|
|
Tell me, how many days should I wait for a response from the support service?
|
|
7
|
159
|
January 19, 2025
|
|
Galvo timing settings -- calibrate for mirror acceleration?
|
|
2
|
137
|
January 15, 2025
|
|
Lightburn doesn't connect to my Raycus QS 30W
|
|
3
|
163
|
January 14, 2025
|
|
Problem with grayscale engraving
|
|
14
|
539
|
January 14, 2025
|
|
Display problems
|
|
4
|
35
|
December 29, 2024
|
|
Why am I disappointed with LightBurn? (questions about the program's critical problems for me)
|
|
21
|
523
|
December 22, 2024
|
|
Ramp Settings Not Cutting The Same as Preview
|
|
7
|
163
|
December 21, 2024
|
|
Uneven burning on electro plated zinc alloy
|
|
12
|
164
|
December 19, 2024
|
|
Fill layer and line layer not aligned
|
|
7
|
142
|
November 30, 2024
|
|
Loss of laser power
|
|
10
|
189
|
November 22, 2024
|
|
Struggling to get lightburn to connect atomstack m4
|
|
6
|
574
|
November 19, 2024
|
|
Rotary Axis as "Z Axis" / lift table- Galvo Fiber
|
|
10
|
223
|
November 17, 2024
|
|
I have had revert back from v7 to last release of 6
|
|
8
|
106
|
November 3, 2024
|
|
Mysterious bumps on my 3D slice engravings
|
|
5
|
377
|
September 29, 2024
|
|
Device will not stay connected to BJJCZ device - Laser Mark Control Board V4
|
|
6
|
410
|
October 23, 2024
|
|
100 watt mopa jpt fiber laser
|
|
7
|
1194
|
October 20, 2024
|
|
Why is power between 50-60% lacking when using LB? There is no problem with the other powers, you can see the laser in the 50%-60% range using EZCAD2
|
|
4
|
110
|
September 23, 2024
|
|
ComMarker B4 20W Fiber Laser Tumbler Settings
|
|
11
|
2266
|
July 30, 2024
|
|
Text in a dxf getting off centered after importing
|
|
1
|
47
|
August 15, 2024
|
|
Fine lines and moiree patterns with 2.5D engraving
|
|
7
|
402
|
July 15, 2024
|
|
Feeltek Controllers and Compatibility
|
|
2
|
174
|
August 11, 2024
|
|
Any Fiber Laser folks in the Ashville area?
|
|
3
|
113
|
June 18, 2024
|
|
New 300 x 300 lens but working area is 120 x 120
|
|
2
|
206
|
July 10, 2024
|