instructables
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser
Rotary
by JoeC297
Have you ever had problems engraving a tapered cup? Do your images come out distorted? Do you want to engrave a
mug with a handle? Then, this instructable is for you!
This is a two-part instructable for laser engraving items on rotary attachments. The �rst half will describe the steps to
build a set of wheels to keep tapered items level on a rotary, or allow mugs with handles to rotate unimpeded. The
second half will detail the process to calculate and adjust an image for engraving on a rotary device. If you already have a
method to rotate your item and just want these calculations, skip to Step 7.
Supplies:
Rotary Adaptor Supplies
Material of choice (wood, acrylic, etc)
Paint or stain to enhance the engravings (optional)
#8-32 machine screws (various sizes)
#8 washers and nuts
#8-32 brass expansion nuts (various sizes)
Rubber stoppers - preferably with a hole (various sizes)
Drill bits (if you need to makes holes in the rubber stoppers)
Rubber bands, wide (optional)
A few links to some of these items:
#8-32 x 15/32 in. Brass Expansion Nut
10x #000 Neoprene Stoppers, 1 Hole
10x #00 Neoprene Stoppers, 1 Hole
2x 0.375-in Black Neoprene Hole Plug
36x #8 Stainless Steel Standard Flat Washer
22x #8 x 32 Zinc-plated Steel Hex Nut
Image Adjustment Supplies
Adobe Acrobat Reader (Free)
Inkscape (Free)
Lightburn (or your laser program of choice)
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 1
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 2
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 3
Step 1: Selecting Your Size Adaptor
This part is dependent on your needs. The easiest method to determine what size you need is to measure the widest part
of your item's opening or base - whichever is larger, and add twice the width of your handle (if engraving a mug). This will
allow the item to rotate evenly without hitting the rotary device. I've included multiple sets of SVGs for 100mm and
150mm guides. For sizing consideration, here are a few options:
If your size requirement is less than 100mm, use the 100mm guide. (For regular tapered tumblers, bottles,
etc.)
If your size requirement is between 100mm and 150mm, use the 150mm guide. (For large tapered
tumblers, bottles, regular mugs with handles, etc.)
If your size requirement is greater than 150mm, start with either the 100mm or 150mm guide that has
alignment lines larger than your item's opening or base and add a circle 10mm larger than the
requirement and center it on the guide. Set this circle to cut, and remove the cut radius for the selected
guide. (For large mugs with handles)
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 4
Example: I measured a large mug that is 105mm wide with a 40mm handle. I require a 185mm guide. I load the 150mm
guide, create a circle 195mm wide and center it on the 150mm guide, and delete the 150mm cut line. Please keep in
mind to watch what direction the image will rotate the handle, and that it doesn't strike your laser head.
Each size guide has two hole alignments, and each set requires both the engraving and cut �les for the guide. The
includes sets are:
100mm guide with holes and alignment lines on the 10s (10, 20, 30, 40, etc.)
100mm guide with holes and alignment lines on the 5s (15, 25, 35, 45, etc.)
150mm guide with holes and alignment lines on the 10s (10, 20, 30, 40, etc.)
150mm guide with holes and alignment lines on the 5s (15, 25, 35, 45, etc.)
Note: I recommend cutting at least one of each of your chosen width. This gives you the option between the two guides
to get within 5mm of the correct diameter for the base of your item - especially if using expansion nuts.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 5
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 6
https://www.instructables.com/ORIG/FLD/0RS9/KZBA3YZV/FLD0RS9KZBA3YZV.svg
Download
https://www.instructables.com/ORIG/FL1/V1I2/KZBA3YZX/FL1V1I2KZBA3YZX.svg
Download
https://www.instructables.com/ORIG/F44/UU04/KZBA3YZW/F44UU04KZBA3YZW.svg
Download
https://www.instructables.com/ORIG/FVB/P83F/KZBA3YZY/FVBP83FKZBA3YZY.svg
Download
https://www.instructables.com/ORIG/F9P/DA83/KZBA3YZZ/F9PDA83KZBA3YZZ.svg
Download
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 7
Step 2: Engrave & Cut Your Wheels
https://www.instructables.com/ORIG/FQJ/1Q4U/KZBA3Z01/FQJ1Q4UKZBA3Z01.svg
Download
https://www.instructables.com/ORIG/FWL/F7AU/KZBA3Z00/FWLF7AUKZBA3Z00.svg
Download
https://www.instructables.com/ORIG/FOJ/EBT6/KZBA3Z02/FOJEBT6KZBA3Z02.svg
Download
Load the �les for your chosen size in your laser program. Select both the engraving circle and the cutting circle, and
center them on each other. Load your material in your machine and begin engraving/cutting as appropriate for your
material in the following order:
Engrave all markings
Cut the guide holes
Cut out the wheel
Originally, I used plywood, and didn't need to do anything to enhance the engravings. However, when I used acrylic, I
applied white paint and wiped it o� to make the engravings easier to see.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 8
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 9
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 10
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 11
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 12
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 13
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 14
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 15
Step 3: Prepare the Grips
I use #8-32 machine screws, #8 washers and #8 nuts to secure my grips. The washers protect the screws from damaging
the outside of the wheel. The nuts allow me to use longer screws on the rubber stoppers to compress them to widen
their grips as needed. I keep a range of grips from expansion nuts to rubber stoppers with holes to allow me a wide range
of options for gripping di�erent shaped items.
If you can't �nd rubber stoppers with holes, you can use a drill with varying sizes of drill bits to drill a hole in the center of
a solid stopper. Begin with the smallest bit, to ensure you guide the bit through the middle. Don't worry if you're a little
o�, as you can correct this as you get closer to your �nal size. I checked the �t with a screw each time I �nished with one
bit, eventually �nishing with 3/16" bit, as I wanted a tight �t. (This will make a mess!)
Note: If you have issues with your wheels slipping due to the material or the grip of the rotary bars, you can add a wide
rubber band around the wheels.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 16
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 17
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 18
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 19
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 20
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 21
Step 4: Attach the Guides to Your Item
Once you have your wheels and hardware ready, it time to put them to use.
First, "measure" the base of your item. I �nd this is the more challenging attachment point, because it is typically attached
on the outside. If you have a longer item and aren't worried about the size of the engravable area, you can use the
rubber stoppers. Otherwise, you can use the expansion nuts, but be careful with the size of these nuts. (Mine are small.)
Place the screws through washers in a circle about 10mm wider than this "measurement". Hand tighten the expansion
nuts or slide on the rubber stoppers, then attach the item by carefully pushing the item into the middle of the grips.
In the example photos, the base measured about 55mm wide, so I placed the expansion nuts at 65mm. This was
su�cient to maintain grip without tightening the nut, but I have tightened the nuts on other items. (It provides another
2-3mm of width on the grip.)
Second, "measure" the top of your item. Place screws through washers in holes 10-20mm inside of that "measurement".
Attach the rubber stoppers by pushing them (or screwing them if you have a very tight �t) onto the screws. If desired,
you can use a nut to provide a slightly wider �t. Attach the item by carefully pushing the item's opening around the grips.
Third, make sure both ends are even. A gap may be visible and is acceptable, as long as the item is secure. A good test is
to roll the item to check how even it is.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 22
Note: Take care to ensure none of the washers or grips extend past the side of the wheel. This may interfere with the
smooth rolling of your rotary device.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 23
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 24
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 25
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 26
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 27
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 28
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 29
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 30
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 31
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 32
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 33
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 34
Step 5: Level the Item and Engrave
At this point, you need to prepare your rotary and the item to ensure the engraving surface is level with your laser. By
using a level, you can ensure your spoilboard and laser are level to the ground. Once this is complete, angle your rotary
in order to make the top of your item level to the ground. Once this is done, you're almost ready to begin your
engraving...
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 35
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 36
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 37
Step 6: Images on Items Will Be Distorted
Unfortunately, round/even items will engrave narrower images and tapered items will engrave conical shaped images.
This distortion is due to the di�erence in rotational distance between the wheel (normal) and the item (slower), as well as
the angle of the item's centerline on tapered items.
In these photos you can see how the example image is narrower and even smaller toward the bottom. The �nal photo is
with an image correction. (There is still a slight curve in the top and bottom due to the angle of the item, but the width is
corrected.) I won't bore you with all of the calculations, so instead I've created a PDF that does the calculations for you.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 38
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 39
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 40
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 41
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 42
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 43
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 44
Step 7: Calculate Image Corrections
In order to use the Rotary Calculations �le, you need:
Width of the wheel (If you are not using guide wheels, or have an adapter the same size as your top on
the bottom end, enter the width of the top of your item.)
Width of the top and bottom of the item
Height of the item
Width and height of the image
Height on the item of the center of the image
Enter all of these items into the Rotary Calculations, and follow the instructions:
If the item has equal sized ends with straight sides, increase the width while maintaining the height to the
adjusted image dimensions.
Otherwise, export the image as an SVG, open the �le in Inkscape and group all of the vectors.
Click Path → Path E�ects…, click the + symbol (Add path e�ect) in the Path E�ects dock, and select
Perspective/Envelope.
Ensure the Type selected is Perspective, change the Handles to the calculated adjustments, and save the
image.
Note: This process tends to break some of the nodes on the vectors. If you have one's set to �ll, the instructions will help
you in Lightburn. If you are using another program, please look for a function that allows you to close the paths.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 45
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 46
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 47
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 48
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 49
Step 8: Engrave!
https://www.instructables.com/ORIG/FBA/97CK/KZCPK8BL/FBA97CKKZCPK8BL.pdf
Download
Your image is now ready to engrave!
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 50
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 51
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 52
Step 9: Bonus Content - Rotary Leveler
There are various ways to level your rotary device depending on which model you have. I own the xTool Rotary
Attachment, which has two very convenient long rectangular openings on the bottom. By measuring the rotary device
and the openings, I built a rotary leveler that incorporated the rails to consistently allow me to attach the rotary device to
the leveler perpendicular to the hinges that angle the mount. (Also added a centerline for the widest setting on my
rotary.) I adjust the angle of the leveler by using bolts with a nut to keep the leveler at the appropriate height.
Unfortunately, I can't address all of the rotary devices out there, but most appear to have parallel sides. If you have one of
these devices, you can mount a simple rail on the "downhill" side of the angle parallel to the hinge to similarly keep it in
place.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 53
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 54
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 55
Step 10: Bonus Content - Stemless Glass Guide
https://www.instructables.com/ORIG/FHN/46K7/KZFKE7IX/FHN46K7KZFKE7IX.svg
Download
If you are trying to engrave on a stemless glass, this method requires a minor adjustment. Since the bottom of most
stemless glasses are rounded, the grips for the guide above will probably not allow a secure attachment. As a result, you'll
need to create a new set of guide wheels. These will be dependent on the widest part of the glass as shown in the
diagram. By following the example in Step 1 for a custom size, create a guide wheel that is the same diameter of the
widest part of the stemless glass. The example glass I used was 75mm wide, and the SVG �les are included below. These
�les include a larger hole in the very center. This hole is intended for a large bolt and as many nuts/washers you'd like to
include for added weight to stabilize the whole setup on your rotary. This will allow two points of contact with the same
diameter - the widest part of the glass and the guide wheel.
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 56
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 57
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 58
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 59
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 60
https://www.instructables.com/ORIG/FJJ/S4SB/KZMPN0I5/FJJS4SBKZMPN0I5.svg
Download
https://www.instructables.com/ORIG/F2T/PJUN/KZMPN0I6/F2TPJUNKZMPN0I6.svg
Download
https://www.instructables.com/ORIG/FZK/91LR/KZMPN1M5/FZK91LRKZMPN1M5.svg
Download
https://www.instructables.com/ORIG/FKE/653T/KZMPN1M6/FKE653TKZMPN1M6.svg
Download
Drinkware Adaptor (Tapered and Mugs) and Image Adjustment for Laser Rotary: Page 61