[15:57:43] [ 3D Viewer ] WebGL Support found! success: this application will work optimally on this device!

[15:57:43] [ Websocket ] Bidirectional Websocket Interface Started

[15:58:01] [ connect ] PORT INFO: Port is now open: /dev/tty.usbserial-AK08TUK0 - Attempting to detect Firmware

[15:58:01] [ connect ] Checking for firmware on /dev/tty.usbserial-AK08TUK0

[15:58:01] [ connect ] Detecting Firmware: Method 1 (Autoreset)

[15:58:02] [ connect ] Detecting Firmware: Method 2 (Ctrl+X)

[15:58:03] [ connect ] Detecting Firmware: Method 3 (others that are not supported)

[15:58:03] [ ] Grbl 1.1f ['$' for help]

[15:58:03] [ ] [MSG:'$H'|'$X' to unlock]

[15:58:03] [ $$ ] $0=10 ;Step pulse time, microseconds

[15:58:03] [ $$ ] $1=255 ;Step idle delay, milliseconds

[15:58:03] [ $$ ] $2=0 ;Step pulse invert, mask

[15:58:03] [ $$ ] $3=1 ;Step direction invert, mask

[15:58:03] [ $$ ] $4=1 ;Invert step enable pin, boolean

[15:58:03] [ $$ ] $5=0 ;Invert limit pins, boolean

[15:58:03] [ $$ ] $6=0 ;Invert probe pin, boolean

[15:58:03] [ $$ ] $10=1 ;Status report options, mask

[15:58:03] [ $$ ] $11=0.020 ;Junction deviation, millimeters

[15:58:03] [ $$ ] $12=0.002 ;Arc tolerance, millimeters

[15:58:03] [ $$ ] $13=0 ;Report in inches, boolean

[15:58:03] [ $$ ] $20=0 ;Soft limits enable, boolean

[15:58:03] [ $$ ] $21=1 ;Hard limits enable, boolean

[15:58:03] [ $$ ] $22=1 ;Homing cycle enable, boolean

[15:58:03] [ $$ ] $23=7 ;Homing direction invert, mask

[15:58:03] [ $$ ] $24=100.000 ;Homing locate feed rate, mm/min

[15:58:03] [ $$ ] $25=1000.000 ;Homing search seek rate, mm/min

[15:58:03] [ $$ ] $26=250 ;Homing switch debounce delay, milliseconds

[15:58:03] [ $$ ] $27=6.000 ;Homing switch pull-off distance, millimeters

[15:58:03] [ $$ ] $30=255 ;Maximum spindle speed, RPM

[15:58:03] [ $$ ] $31=0 ;Minimum spindle speed, RPM

[15:58:03] [ $$ ] $32=0 ;Laser-mode enable, boolean

[15:58:03] [ $$ ] $100=57.143 ;X-axis steps per millimeter

[15:58:03] [ $$ ] $101=57.143 ;Y-axis steps per millimeter

[15:58:03] [ $$ ] $102=57.143 ;Z-axis steps per millimeter

[15:58:03] [ $$ ] $110=5000.000 ;X-axis maximum rate, mm/min

[15:58:03] [ $$ ] $111=5000.000 ;Y-axis maximum rate, mm/min

[15:58:03] [ $$ ] $112=5000.000 ;Z-axis maximum rate, mm/min

[15:58:03] [ $$ ] $120=500.000 ;X-axis acceleration, mm/sec^2

[15:58:03] [ $$ ] $121=500.000 ;Y-axis acceleration, mm/sec^2

[15:58:03] [ $$ ] $122=500.000 ;Z-axis acceleration, mm/sec^2

[15:58:03] [ $$ ] $130=800.000 ;X-axis maximum travel, millimeters

[15:58:03] [ $$ ] $131=800.000 ;Y-axis maximum travel, millimeters

[15:58:03] [ $$ ] $132=70.000 ;Z-axis maximum travel, millimeters

[15:58:03] [ $$ ] ok

[15:58:03] [ $I ] [VER:1.1f.20170302:ACRO1010PEN]

[15:58:03] [ $I ] [OPT:QVH,15,128]

[15:58:03] [ $I ] ok

[15:58:05] [ connect ] Firmware Detected: grbl version 1.1f on /dev/tty.usbserial-AK08TUK0