Ortur LM 2 pro stops after about 3 mins

[KBar87 (Ken)]

I am trying to burn a grid and the job stops after 3.5 mins. I tried restarting a few times but I keep getting the same results. I have attached the readout from the console as well as screenshots from various settings. I have never had something like this happen. I am lost right now. Any assistance would be great.
Thank you,
-Ken

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 191.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG:Warning: Flame Sensor Disabled by User OverRide]

[MSG:Flame detector active,Ambient infrared value:0]

Grbl 1.1f [‘$’ for help]

[MSG:‘$H’|‘$X’ to unlock]

[MSG:Caution: Unlocked]

ok

ok

<Idle|MPos:0.000,0.000,0.000|Bf:35,7679|FS:0,0|Pn:P|CL:0,100|PS:2,1|ER:0,0|VA:24665,0|Ov:100,100,100|A:S|H:1,7>

ok

Starting stream

Layer C01

[MSG:]

ALARM:2

G-code motion target exceeds machine travel. Machine position safely retained. Alarm may be unlocked. (Right-click the ‘Devices’ button to reset the connection)

On or near line 0:

Job halted

Stream completed in 3:20

[MSG:Reset to continue]

ok

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 191.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG:Warning: Flame Sensor Disabled by User OverRide]

[MSG:Flame detector active,Ambient infrared value:0]

Grbl 1.1f [‘$’ for help]

[MSG:‘$H’|‘$X’ to unlock]

[MSG:Caution: Unlocked]

ok

$0=5.0

$1=100

$2=0

$3=6

$4=7

$5=7

$6=1

$10=2047

$11=0.050

$12=0.002

$13=0

$14=6

$15=0

$16=1

$17=4

$18=0

$19=0

$20=1

$21=1

$22=1

$23=7

$24=600.000

$25=3000.000

$26=100

$27=3.000

$28=0.100

$29=0.0

$30=1000.

$31=0.

$32=1

$33=1000.000

$34=0.000

$35=0.000

$36=100.000

$37=0

$39=1

$40=1

$41=0

$42=1

$43=1

$44=3

$45=0

$46=0

$56=1.000

$57=1800.000

$58=395.000

$59=6000.000

$60=0

$61=0

$62=0

$63=3

$64=1

$65=0

$100=80.000

$101=80.000

$102=2124.000

$110=10200.000

$111=10200.000

$112=600.000

$120=2200.000

$121=1800.000

$122=200.000

$130=400.500

$131=400.500

$132=100.000

$259=0

$260=70

$261=0

$262=400

$263=0

$264=0

$265=50

$266=100

$267=0

$268=0

$269=0

$270=5120

ok

$0=5.0

$1=100

$2=0

$3=6

$4=7

$5=7

$6=1

$10=2047

$11=0.050

$12=0.002

$13=0

$14=6

$15=0

$16=1

$17=4

$18=0

$19=0

$20=1

$21=1

$22=1

$23=7

$24=600.000

$25=3000.000

$26=100

$27=3.000

$28=0.100

$29=0.0

$30=1000.

$31=0.

$32=1

$33=1000.000

$34=0.000

$35=0.000

$36=100.000

$37=0

$39=1

$40=1

$41=0

$42=1

$43=1

$44=3

$45=0

$46=0

$56=1.000

$57=1800.000

$58=395.000

$59=6000.000

$60=0

$61=0

$62=0

$63=3

$64=1

$65=0

$100=80.000

$101=80.000

$102=2124.000

$110=10200.000

$111=10200.000

$112=600.000

$120=2200.000

$121=1800.000

$122=200.000

$130=400.500

$131=400.500

$132=100.000

$259=0

$260=70

$261=0

$262=400

$263=0

$264=0

$265=50

$266=100

$267=0

$268=0

$269=0

$270=5120

ok

ok

ok

ok

<Idle|MPos:0.000,0.000,0.000|Bf:35,7679|FS:0,0|Pn:P|CL:0,100|PS:2,1|ER:0,0|VA:24665,0|Ov:100,100,100|A:S|H:1,7>

ok

Starting stream

Layer C01

[MSG:]

[MSG:]

ALARM:2

G-code motion target exceeds machine travel. Machine position safely retained. Alarm may be unlocked. (Right-click the ‘Devices’ button to reset the connection)

On or near line 0:

Job halted

Stream completed in 3:30

[MSG:Reset to continue]

ok

Ortur Laser Master 2 Pro S2 Ready!

OLF:OLF 191.

OLH:OLM_ESP_PRO_V1.2.

OLM:GENERAL.

[MSG:Warning: Flame Sensor Disabled by User OverRide]

[MSG:Flame detector active,Ambient infrared value:0]

Grbl 1.1f [‘$’ for help]

[MSG:‘$H’|‘$X’ to unlock]

[MSG:Caution: Unlocked]

ok

[Jomimar (jose)]

Hello, the same thing is happening to me, with lightburn it stops, but I use lasergrbl and it works, I have deleted and installed again without updating and nothing remains the same…
I have a treestwo ts 55 pro with laser 10 w.

[bionicback321 (Paul)]

Question: Does it stop (fail) at the end of layer 1 (grid) and before the start of layer 2 (the logo)? If so, do a preview with “show traversal moves” on and see if they go outside of your workspace. I’ve had something like this happen when the speed was too high and there wasn’t enough room for the head to slow down and reverse direction. Just a wag on my part.

[KBar87 (Ken)]

Same for me, it ran fine in laser grbl. I think it’s an error in a setting in lightburn, but I have no idea where to look.

[Jomimar (jose)]

Hello, at the moment it is working well for me, I have been trying all the USBs on the computer, until one started working for me. At the moment it works well, let’s see it works perfectly

[KBar87 (Ken)]

It doesn’t finish the grid it gets half way through it, laser turns off. If I press pause and than resume on lightburn it continues again for about a minute. The weird thing is that I exported the lightburn file as an SVG and ran it in lasergrbl and it went flawless.

[bionicback321 (Paul)]

Sorry it took so long to get back to you. I have an OLM2 Pro S1, if you feel like sharing the .ibrn file here, I can run it on my machine and see what happens.