|
Welcome to Discourse
|
|
1
|
10303
|
January 22, 2019
|
|
Connection port failed to open
|
|
0
|
12
|
April 16, 2024
|
|
LightBurn not connecting to engraver
|
|
7
|
47
|
April 16, 2024
|
|
Laser always on at 100% power
|
|
9
|
68
|
April 16, 2024
|
|
Printing to printer
|
|
1
|
20
|
April 16, 2024
|
|
ALARM:3 Reset while in motion. Grbl cannot guarantee position. Lost steps are likely. Re-homing is highly recommended
|
|
0
|
10
|
April 16, 2024
|
|
Genmitsu 3018-Pro CFL55P Laser Always On
|
|
2
|
9
|
April 16, 2024
|
|
Atezr 36w Cutting 1/2" Material
|
|
7
|
57
|
April 16, 2024
|
|
To really understand Lasers
|
|
1
|
29
|
April 16, 2024
|
|
How to transfer license key from old mac to new one?
|
|
7
|
68
|
April 16, 2024
|
|
Step Idle Delay setting not working (Setting $1=255)
|
|
2
|
16
|
April 16, 2024
|
|
Teaching hardware to Lightburn
|
|
1
|
17
|
April 16, 2024
|
|
New lamp prototype
|
|
33
|
1122
|
April 16, 2024
|
|
Lightburn is not centering object when using absolute coordinates
|
|
0
|
22
|
April 16, 2024
|
|
Gweike G2 Fiber Laser Not Connecting on M1 Mac
|
|
4
|
59
|
April 16, 2024
|
|
The laser engraver incorrectly identified the engraving stage
|
|
12
|
68
|
April 16, 2024
|
|
Using diode laser on Rowmark
|
|
0
|
15
|
April 16, 2024
|
|
Anybody have experience with a Send Cut Send controller?
|
|
9
|
86
|
April 16, 2024
|
|
Modifying settings for 80w
|
|
0
|
15
|
April 16, 2024
|
|
Preview Time not accurate ( already did "Read from controller" )
|
|
68
|
276
|
April 16, 2024
|
|
Tapemanblue transfer tape for vinyl
|
|
8
|
97
|
April 16, 2024
|
|
Cannon burn an image larger than 65.534mm
|
|
7
|
73
|
April 16, 2024
|
|
Only Framing half way and then stops
|
|
10
|
64
|
April 16, 2024
|
|
Linux Commarker B4 setup in Lightburn
|
|
28
|
257
|
April 16, 2024
|
|
Rotary engraving -- skips too fast between shapes
|
|
4
|
33
|
April 16, 2024
|
|
Multiple firmware updates
|
|
1
|
28
|
April 15, 2024
|
|
Does powering the bridge on/off with a switch cause any damage? Or keep it on all the time?
|
|
2
|
32
|
April 15, 2024
|
|
Como cambiar numero en una matriz
|
|
5
|
26
|
April 15, 2024
|
|
Xtool Machine On and Off Light
|
|
6
|
40
|
April 15, 2024
|
|
Error message when trying to start engraving
|
|
6
|
29
|
April 15, 2024
|