|
About the Ortur Lasers category
|
|
0
|
1552
|
September 1, 2020
|
|
Ortur LM2 movement issue
|
|
7
|
52
|
December 25, 2025
|
|
The Ruler doesnt show the modified result
|
|
1
|
25
|
December 23, 2025
|
|
Unable to adjust the power always 100%
|
|
5
|
794
|
December 23, 2025
|
|
Error:1 G-code words....Burn stops after a few seconds with error
|
|
4
|
43
|
January 10, 2026
|
|
OLM Pro 2 S1 flame detector active
|
|
5
|
62
|
January 2, 2026
|
|
Ayuda con mi laser
|
|
2
|
27
|
December 20, 2025
|
|
Possible Bug - Tabs fail on layers with multiple passes
|
|
2
|
31
|
December 12, 2025
|
|
Ortur LM2 Pro S1 Not Firing - Advice
|
|
14
|
147
|
December 11, 2025
|
|
Ortur LM2 Pro - S1 where are the firmware I am in 170
|
|
3
|
40
|
December 10, 2025
|
|
Ortur LM2 Pro S2 freezes in Busy state in LightBurn (works fine in LaserGRBL)
|
|
42
|
293
|
December 4, 2025
|
|
Ortur Laser Master 2 Pro S2 - Firmware Update FAIL
|
|
1
|
41
|
December 2, 2025
|
|
ORTUR LASER MASTER 2 PRO S1 & S2 Firmware update
|
|
12
|
5628
|
November 2, 2025
|
|
Patchy/Unfinished printing?
|
|
22
|
86
|
November 10, 2025
|
|
Laser won't engrave or cut
|
|
12
|
126
|
November 9, 2025
|
|
OLM3 engraving tall from one pc, but not another
|
|
5
|
53
|
October 24, 2025
|
|
Laser Ortur Master 3LE no enciende la luz
|
|
4
|
58
|
October 17, 2025
|
|
Ortur Laser Master 2 S2 travel speed and instability
|
|
3
|
59
|
October 8, 2025
|
|
Converting a LC-60A to use LU2-10A
|
|
2
|
45
|
October 7, 2025
|
|
Ortur laser master pro 2 binding up
|
|
2
|
38
|
October 6, 2025
|
|
Problème de tensions ? Ou peut-être autre chose?
|
|
2
|
38
|
October 2, 2025
|
|
Low pwm voltage on main board
|
|
4
|
81
|
September 26, 2025
|
|
Startup Alarm-9 Homing Error with Aufero AL1 and Rotary Chuck
|
|
7
|
71
|
September 22, 2025
|
|
Laser Master 2 Pro S1
|
|
15
|
106
|
September 19, 2025
|
|
Ortur alarms and out of bounds warnings
|
|
4
|
2696
|
August 8, 2025
|
|
3018 Pro Laser Positioning Issues
|
|
6
|
92
|
September 1, 2025
|
|
Sad new user: can't get past "error:20 Unsupported or invalid g-code command found in block"
|
|
35
|
8495
|
August 1, 2025
|
|
Ortur Z-Height Adjuster WOBBLES!
|
|
4
|
67
|
August 23, 2025
|
|
OLM3 not working anymore, constantly on reset mode (RGB cycle) ; Firmwares updates all failing
|
|
1
|
56
|
August 12, 2025
|
|
OLM2 - Adding Z-Axis Stepper Driver to Mainbaord
|
|
44
|
6288
|
July 9, 2025
|