|
Software ortur issues
|
|
6
|
123
|
June 15, 2026
|
|
Ortur not adjusting speed settings after update
|
|
2
|
52
|
June 3, 2026
|
|
No response using Ortur Pro 2
|
|
4
|
53
|
April 8, 2026
|
|
Ortur Laser Master 2 S2 Alarm 9 Homing Fail on startup
|
|
2
|
92
|
February 6, 2026
|
|
Ortur LM2 Pro S1 Not Firing - Advice
|
|
13
|
282
|
November 11, 2025
|
|
Ortur Laser Master 2 Pro S2 - Firmware Update FAIL
|
|
0
|
74
|
November 2, 2025
|
|
Problème de tensions ? Ou peut-être autre chose?
|
|
1
|
55
|
September 2, 2025
|
|
MKS DLC32 V2.1 + P-DA-01 + LaserTree 30W – Not cutting at higher speeds / Laser shuts off with driver
|
|
6
|
601
|
June 24, 2025
|
|
Can I stick the LU2-10A on the Laser Master Pro 2, S1? (not the S2)
|
|
5
|
222
|
April 7, 2025
|
|
RUBBER STAMP materials
|
|
4
|
280
|
January 18, 2025
|
|
Ortur LM2 10w not cutting clean
|
|
7
|
260
|
January 6, 2025
|
|
Ortur laser master 3 flashing yellow and red and beeping
|
|
1
|
92
|
December 5, 2024
|
|
Zero Point Rotary Setup
|
|
2
|
112
|
November 16, 2024
|
|
Odd line spacing when using bi-directional fill
|
|
4
|
168
|
September 27, 2024
|
|
Getting error Alarm:2 may have wrong firmware
|
|
1
|
45
|
September 16, 2024
|
|
Ortur Laser Master 2 Motherboard Issues
|
|
8
|
726
|
September 11, 2024
|
|
Issue with laser and table calibration
|
|
0
|
67
|
September 3, 2024
|
|
New Laser Master 2 S2 Setup and Calibration
|
|
1
|
405
|
August 5, 2024
|
|
Problem with random horizontal lines on my engraving
|
|
4
|
309
|
June 23, 2024
|
|
Connecting to OLM2PROS2 via WI-FI
|
|
2
|
206
|
June 15, 2024
|
|
Enlarge bed for Ortur LM2
|
|
4
|
459
|
April 2, 2024
|
|
ALARM:2 G-code motion target exceeds machine travel. Mac OS 11.7.10
|
|
8
|
200
|
March 24, 2024
|
|
Laser "acts" like it doesn't know where it is at
|
|
3
|
257
|
November 14, 2023
|
|
Uneven Fill- What causes this?
|
|
3
|
370
|
November 8, 2023
|
|
Ortur laser master pro 2 engraving squares as rectangles
|
|
2
|
299
|
October 29, 2023
|
|
Ortur laser master 2 pro not working
|
|
2
|
403
|
August 10, 2023
|
|
Problems during firmware upgrade of OLM2 pro S2
|
|
3
|
932
|
July 17, 2023
|
|
Just getting 'Waiting for Connection...'
|
|
1
|
331
|
June 8, 2023
|
|
Ortur laser master 2 Pro
|
|
1
|
400
|
May 18, 2023
|
|
Additional GCode M14 (Fan on) not working - manual gcode command works
|
|
3
|
1299
|
April 8, 2023
|