|
About the Ruida controllers category
|
|
3
|
4291
|
April 13, 2024
|
|
OMtech laser Frames correctly but lasers out of alignment
|
|
15
|
40
|
May 3, 2024
|
|
Fill Issue. Looks like Laser turns off too slow
|
|
5
|
32
|
May 3, 2024
|
|
Ruida Emulator Software
|
|
3
|
61
|
May 2, 2024
|
|
Red & Black 80W CO2 - Stepper Motor Replacement Options
|
|
12
|
178
|
May 2, 2024
|
|
Laser does not fire
|
|
2
|
50
|
April 30, 2024
|
|
Material Test Generator - Same Power on all squares
|
|
0
|
41
|
April 28, 2024
|
|
XY Axis Over Scale
|
|
18
|
176
|
April 26, 2024
|
|
Horizontal lines and distortion
|
|
3
|
39
|
April 25, 2024
|
|
Adjustable bed drive belt
|
|
4
|
100
|
April 10, 2024
|
|
Y-axis Offset on OmTech
|
|
1
|
40
|
April 24, 2024
|
|
Constant power problem (cont)
|
|
0
|
39
|
April 24, 2024
|
|
Ruida vs LinuxCNC
|
|
1
|
48
|
April 23, 2024
|
|
Is this whining noise a setting, or a hardware fault?
|
|
8
|
68
|
April 22, 2024
|
|
Squeezed text when use rotary (wider and less high)
|
|
14
|
137
|
April 19, 2024
|
|
Lightburn randomly closing while I’m using it
|
|
1
|
55
|
April 18, 2024
|
|
10000 mm on x&y axis
|
|
4
|
73
|
April 17, 2024
|
|
Not enough Buffer Space
|
|
8
|
123
|
April 15, 2024
|
|
Lettering has shadow on leatherette-Help!
|
|
8
|
59
|
April 12, 2024
|
|
CO2 Laser Engraves but Doesn't Cut
|
|
41
|
376
|
April 9, 2024
|
|
Stepper Motor Driver Issue (Alarm)
|
|
6
|
74
|
April 9, 2024
|
|
Wiggly Lines On X Axis
|
|
3
|
83
|
May 2, 2024
|
|
Help! Laser head crashed and belt slipped. I need to reset 0,0 HOME POSITION
|
|
4
|
135
|
May 1, 2024
|
|
AP LAZER SN4024 settings?
|
|
1
|
49
|
April 30, 2024
|
|
Turning on extractor and air assist based on project start/stop
|
|
6
|
127
|
April 26, 2024
|
|
Layers being changed when opening RD file
|
|
2
|
99
|
April 25, 2024
|
|
Ruida Homing Issues
|
|
19
|
211
|
April 22, 2024
|
|
Constant power problem
|
|
16
|
227
|
April 20, 2024
|
|
Lines shifts during a burn
|
|
11
|
154
|
April 20, 2024
|
|
Run servo motors with ruida controllers
|
|
5
|
201
|
April 15, 2024
|