Hardware

Yora A place for anything related to the Yora system hardware. Cameras Anything related to camera use with LightBurn - models, setup, etc. Snapmaker Here is the location to post all things Snapmaker. Smoothieware Smoothieware specific configuration, settings, and issues. NEJE Here is the location to post all things NEJE. Trocen AWC controllers Trocen specific configuration, settings, and issues. GRBL GRBL specific configuration, settings, and issues. Ruida controllers Ruida specific configuration, settings, and issues. TwoTrees A place for anything related to the TwoTrees diode laser hardware. Atomstack A place for anything related to Atomstack A5 or Atomstack A5 Pro Laser Engraver hardware. Ortur Lasers A place for anything related to Ortur Laser Master or Laser Master 2 hardware. TopWisdom controllers TopWisdom specific configuration, settings, and issues. Marlin Marlin specific configuration, settings, and issues.

Topic	Replies	Views	Activity
About the Hardware category Hardware	3	1668	May 7, 2019
Restart a job that was interuptted NEJE	2	21	September 28, 2021
Trocen AWS708S Not communicating Hardware	5	27	September 28, 2021
Ruida controller not reading limit switch Ruida controllers ruida	16	52	September 28, 2021
Hardware help needed Hardware	0	19	September 28, 2021
'New' 32 bit board - anyone try it? GRBL	1	26	September 28, 2021
Neje Master 2s plus is not running on MacBook Pro M1 NEJE	5	38	September 28, 2021
New laptop problems Ortur Lasers	1	30	September 28, 2021
Lightburn or laser stops engraving after 24 minutes, project is not finished Ortur Ortur Lasers	3	24	September 28, 2021
Rotary Attachment - Noob Question Hardware rotary	3	29	September 28, 2021
HELP Gcode 9 locked out GRBL grbl	0	16	September 27, 2021
I have to re-add the laser every session Ortur Lasers	0	21	September 27, 2021
Scanning type camera idea Cameras	2	25	September 27, 2021
My cut line is offset to the left if my engraving Ruida controllers	22	186	September 27, 2021
Ruida configuring homing direction Ruida controllers ruida	1	21	September 27, 2021
Motherboard failure Ortur Lasers	0	22	September 27, 2021
Hook-up For a MKS DLC v2.0 Board GRBL grbl	0	17	September 27, 2021
Ortur Laser Master 2 Pro "Error 24" stopping progress mid burn Ortur Lasers	0	19	September 27, 2021
Rotary on U Axis Ruida. Quick Question Ruida controllers ruida	9	67	September 27, 2021
Lightburn Wi-Fi Bridge with Raspberry Pi 3b+ (USB Question) Hardware camera	32	353	September 27, 2021
Flame Detector inactive error 9 guide locked out during alarm jog Ortur Lasers	0	20	September 27, 2021
Flame alarm keeps going off! Ortur Lasers	2	35	September 27, 2021
Choosing correct communication cable Hardware	3	27	September 27, 2021
How to get simultaneous fill and line when using Ortur YYR Rotary Roller Ortur Lasers	6	81	September 27, 2021
Ortur Laser Master Pro 2 Upgraded Z-axis Ortur Lasers grbl	1	32	September 27, 2021
Ortur rotary roller: infinite y axis? Ortur Lasers	1	23	September 27, 2021
Fill and Line setting not lining up Ortur Lasers	4	104	September 26, 2021
Camera Resolution Adjustment in Lightburn Hardware camera	0	22	September 26, 2021
Can I use OV5648 at full resolution? Cameras	0	21	September 26, 2021
Gcode for KineticNC (Beamicon) based controllers Hardware	1	23	September 26, 2021