|
Diode Laser Questions and Sanity Checks
|
|
10
|
2057
|
February 16, 2022
|
|
Yorahome 6550 40 watt using pc running out of bounds no limit switches + jog buttons backwards
|
|
7
|
1144
|
March 18, 2022
|
|
Hilfe er Lasert nicht (Help he does not laser)
|
|
2
|
2218
|
March 18, 2022
|
|
Laser Origin Position Please help
|
|
7
|
1517
|
March 18, 2022
|
|
Lightburn Camera mounts size
|
|
2
|
497
|
March 18, 2022
|
|
MKS DLC32 V2 + laser k40
|
|
5
|
6966
|
March 18, 2022
|
|
Controller w/ True Rotary (A-Axis)
|
|
12
|
696
|
March 18, 2022
|
|
Fill and Line progressively out of sync from one side to the other, plus related problem
|
|
11
|
911
|
March 17, 2022
|
|
Adding Atomstack X7/A10/S10 in Lightburn
|
|
4
|
18248
|
March 17, 2022
|
|
[MSG:'$H'|'$X' to unlock]
|
|
2
|
2270
|
March 17, 2022
|
|
Aufero 1 Ortur stops engraving at high speeds + high power
|
|
10
|
922
|
March 17, 2022
|
|
Camera Alignment issue- Macbook Big Sur Won’t capture image
|
|
4
|
461
|
March 17, 2022
|
|
Lens calibration: Score too low
|
|
5
|
913
|
February 15, 2022
|
|
Open existing drawing, full scale
|
|
4
|
727
|
March 17, 2022
|
|
Air assist on ortur laser master 2 20 W
|
|
12
|
8070
|
February 15, 2022
|
|
Distorted engraved offset lettering lettering
|
|
4
|
477
|
March 17, 2022
|
|
Tumbler on chuck rotary moving up and down, jaw alignment?
|
|
8
|
1309
|
March 17, 2022
|
|
Less Power After Adding G8 Lens on Ortur LM2
|
|
4
|
542
|
March 17, 2022
|
|
Rotary issues : laser grid numbers in negative x-396 y-396 after unplugging Rotary YRR
|
|
4
|
972
|
February 15, 2022
|
|
Ortur printing wide lines in Lightburn
|
|
9
|
808
|
February 14, 2022
|
|
Snapmaker 2.0: edges burn darker on fill, regardless of overscan setting and fast whitespace scan setting
|
|
9
|
2195
|
March 16, 2022
|
|
Rotary not working on xtool d1
|
|
3
|
2423
|
March 16, 2022
|
|
130W Omtech Only firing while framing
|
|
6
|
713
|
March 16, 2022
|
|
Losing alignment when traveling, can't make acceleration change write to hardware, xTool D1
|
|
59
|
6180
|
March 16, 2022
|
|
Why would the same speed cut deeper at lower power settings?
|
|
24
|
1715
|
March 16, 2022
|
|
Atomstack S10 Pro X7 Pro settings
|
|
7
|
14193
|
March 16, 2022
|
|
I am lost: Wavy lines / Distortion
|
|
1
|
385
|
March 16, 2022
|
|
New setup of TLC Rotary spins and spins does not complete simple rectangle
|
|
11
|
1391
|
March 16, 2022
|
|
My relatively cheap camera solution... it just works
|
|
22
|
7204
|
March 15, 2022
|
|
Lightburn camera for K40
|
|
2
|
341
|
March 15, 2022
|